Confirm by pressing the O.K. button. If you use the built-in monitor loudspeaker, set the volume level in the OSD menu to the middle setting. Use the + and - buttons on the remote control to adjust the navigation audible messages. -3- MONITOR SPECIFICATIONS 1. Type: 2. Display Screen Size: 3. Resolution: 4. Monitor Characteristics: 5. Remote Operation: 6. Power Source: 7. Power Consumption: 8. Maximum Brightness: 9. Operating Temperature: 10. Monitor Cabinet Dimensions: 11. Weight

5. While in the video adjustment mode, press the up button (5) to increase the selected adjustment level or press the down button (6) to decrease the level. GENERAL INSTALLATION INFORMATION 1. Installation will vary from vehicle to vehicle, as headrests in vehicles are not standard. 2. This unit is intended for installation by professional installers. 3. The kit consists of the screen assembly, a mounting housing, key to remove screen from housing, wiring harness and remote control unit. 4. To r

5.6" Active Matrix LCD Monitor Owner.s Manua. EXPLANATION OF GRAPHIC SYMBOLS CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL The lightning flash with the arrowhead within a triangle is intended to alert tell the user that parts inside the product are capable of producing an electric shock . The exclamation point within a triangle is intended to a

Power On/Off Switch 3. Remote Control Sensor 4. Picture Select 5. On Screen Adjustment Up Button 6. On Screen Adjustment Down Button 4 To IR Tansmitter (Optional) 10 9 7 8 12 11 REAR PANEL To Optional IR Transmitter Part Number IRT456 NOTE(B) NOTE(A) 7. Power Input Connector: Red = +12 VDC Black = ground 8. Video Signal Input Connector 9. IR Repeater Connector 10. IR Repeater Transmitter 11. Audio Right Channel Input Connector 12. Audio Left Channel Input Connector 5 Note A : This cable (10) is

Contents.......................................................................................3 D.Positioning the Monitor.................................................................3 E.Controls/Indicators/Connectors...................................................4 F. Powering the Unit.........................................................................4 G. Connecting the Monitor................................................................5 H. Using External Audio/Video Sources (R

3) Generally, the best location for the video monitor is where the vehicle's factory dome light is installed. The monitor should be located in such a manner that it can be comfortably viewed by rear seat passengers. NEVER INSTALL THE MONITOR IN A PLACE WITHIN THE DRIVER'S VIEW. THIS IS NOT ONLY DANGEROUS, BUT IT IS ALSO ILLEGAL IN MANY STATES. 4) Once the mounting location of the monitor has been determined, there may be additional preparation work necessary, depending on the vehicle structure a

By bending the cut back and forth several times, the plastic will break cleanly at the cut. D) Check the fit of the trimmed console and make any minor adjustments necessary. 4) The mini-console can be painted or covered with a material that matches the headliner before assembling the mini-console to video monitor. 5) The finished mini-console should be attached to the video monitor, then attach the assembly to the roof. Tape marker to screwdriver. Starting at your mark for the lowest point, trac

Verify that the source is on and playing a known good media (such as a videotape). Verify connections at both ends of the source component harness. -Push and hold the volume up button until sound is heard over headphones. If problem is limited to the dash radio, verify radio is tuned to the correct channel, and that power to the wired RF modulator is on. (Refer to instructions with modulator kit). Otherwise, verify all connections per the wiring diagram on page 6. -Press Auto Program button. The

logram, Rotation, 6500K, 9300K, User's Color, Degauss, H/V Moire Reduce, Recall, Language, Exit OSD Language: English, French,German, Portuguese,Spanish & Italian Plug & Play: VESADDC1/2B Emissions Standard: North America:TC092; Europe:TC099 Regulations: UL,FCC,FDA,CSA, TUV/GS,CE (Europe Only) Weight: Net:40lbs (18.2kg) - Gross:46.6lbs (21.2kg) Dimensions (W x H x D mm): Monitor:446 x 436 x 455 - Carton:540 x 528 x 570 Dimensions (W x H x D inches): Monitor: 17.6 x 17.2 x 17.9 - Carton:21.3 x

Weight: 1 lb (400g) 11. Video Format: NTSC 3 CONTROLS AND INDICATORS FRONT PANEL 1. Power On LED Indicator 2. Power On/Off Switch 3. Remote Control Sensor 4. Picture Select 5. On Screen Adjustment Up Button 6. On Screen Adjustment Down Button 4 REAR PANEL 10781211 Part Number IRT456 NOTE(B)NOTE(A) To Optional IR Transmitter 7. Power Input Connector: Red = +12 VDC Black = ground 8. Video Signal Input Connector 9. IR Repeater Connector 10. IR Repeater Transmitter 11. Audio Right Channel Input Conn