“ Factory Reservations have approximate size & centering. *** Requires the use of Mac Adapter UNIMAC-82D -17 - Trouble Shooting If trouble occurs in the display unit, perform the following checks and take the indicated action; if the trouble persists, please consult with your dealer. Symptom Check Action nun — There is no display please use upper case for example power cord/plug, power switch signal cable The power saving function might have acted (if so the pilot LED will be yellow). P

This equipment is designed to be used in a household environment, However, if it is used near radio and television receiver units, radio disturbances can occur. Use this equipment appropriately according to the instruction manual. Notice for Germany HINWEIS • Aus ergonomischen Gründen wird empfohlen, die Grundfarbe Blau nicht auf dunklem Untergrund zu verwenden (schlechte Erkennbarkeut, Augenbelastung bei zu geringem Zeichenkontrast wäre die Folge). Achtung: • Für den sicheren Betrieb des M

How To Use On Screen Menu REMOTE CONFIG [REMOTE CONFIG] >GPI1 UNDEF GPI2 UNDEF GPI3 UNDEF GPI4 UNDEF GPI5 UNDEF GPI6 UNDEF GPI7 UNDEF GPI8 UNDEF REMOTE CONFIG menu With REMOTE CONFIG selected, the following menu will appear. GPI1–GPI8 Used to set the pin assignment of REMOTE control terminal. The settable items are same for each terminal. For each function of set-value, refer to the “REMOTE specifications.” Set-value (underlined is default value) UNDEF MARKER1 ON/OFF MARKER2 ON/OFF MARKER HALF*1

U.S.FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INFORMATION TO THE USER NOTE : This equipment has Class B digital device pursuant These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particula

For Daewoo technical support call 1-800-245-9870.) Model : 531X DAEWOO ELECTRONICS CO., LTD. http : //svc.dwe.co.kr September, 2000 CONTENTS SAFETY PRECAUTIONS GENERAL SAFETY INFORMATION SERVICING PRECAUTIONS TECHNICAL INFORMATION GENERAL INFORMATION PIN CONNECTOR CAUTIONS FOR ADJUSTMENT AND REPAIR OPERATION AND ADJUSTMENT 9 ALIGNMENT PROCEDURE 12 TROUBLESHOOTING HINTS 15 BLOCK DIAGRAM 29 PCB LAYOUT 30 SCHEMATIC DIAGRAM 33 EXPLODED VIEW DIAGRAM 37 INFORMATION OF PART DESCRIPTION 38 ELECTRICAL PA

Resolution WSXGA+ 1680 x 1050 Pixel Pitch 0.282mm Brightness 300cd/m2 (Typical) Contrast Ratio 3000:1 (DCR) Surface Treatments Hard Coating (3H), Anti-glare Treatment Viewing Angle (H/V) 170°/160° (Typical) Display Color 16.7M Response Time 3ms (GTG) Frequency (H/V) H: 24kHz - 83kHz V: 50Hz - 76Hz Max. Pixel Clock 190 MHZ Life Time 50,000hrs (Minimum) Input Analog 15-Pin D-Sub Digital 24-Pin DVI-D Audio Audio In 3.5mm Audio Line-in Audio Out 3.5mm Headphone Jack Speak

The number of each monitor appears on its screen. (On some models, the control panel has a different name.) Working with the Control Strip You can move, collapse, and expand the Control Strip, and you can change the order of the controls. Tab m To move the Control Strip, hold down the Option key on your keyboard and drag the tab at the right end of the Control Strip. The Control Strip always stays on the left or right edge of a screen. m To make the Control Strip shorter or longer, drag the tab

Open the “Display Properties Control Panel” by right clicking on the desktop, then select “Properties”. Figure 33 BarcoMed Hardware Tab under Windows 2000 or Windows XP Device Displays the current BarcoMed display controller, driver, and the currently selected display resolution. System manual E1 BarcoMed Hardware Tab Information Device ID: Displays the device’s PCI Device ID number. Vendor ID: Displays the device manufacturer’s PCI Vendor ID number. Subsystem ID: Displays the device’s PCI Subsy

When do you need to use the Autoset functions? It is necessary to perform the Auto Gain and Auto Phase calibrations in the following cases: • The first time you use the display on an analog video • After connecting or selecting another analog video source It is necessary to perform the Automatic Geometry function in case you notice the image geometry or positioning is not as desired. Required test pattern To obtain good results with the autoset functions, it is necessary to have a good image on