50 diagrams the RJ-45 pinouts and signals for the Ethernet RJ-45 connector and cable. FIG. 50 RJ-45 wiring diagram VG-Series Modero Touch Panels Installation Procedures: 12" and 15" Panels VG-Series Modero Touch Panels Installation Procedures: 17" Panels Installation Procedures: 17" Panels Overview NXT panels are mounted onto flat (horizontal) surfaces in either a stand-alone or combo (NXT atop an NXABASE/ B battery base) configuration. NXD panels are installed into either a pre-wall surface (us

1 MVP-7500 Wireless Touch Panel (FG5965-01) ATTENTION! Verify the NetLinx Master Firmware is build 117 or greater for the ME260 and NI-Series Controllers. Verify the TPDesign4 program being used is Version 2.2 or higher. Earlier versions of the Master firmware and TPD4 software are incompatible with these panels. Overview The AMX MVP-7500 panel (FG5965-01) uses an internal wireless compact flash card to communicate with a NetLinx Master via an off-the-shelf 802.11b Wireless Access Point. MVP uni

This is the only method of programming the TPI/3 using Serial Commands. • AXlink connection: Connect a DB-9 cable from your PCCOM port to the Programming port on the Controller. Then use an AXlink cable to connect the AXlink connector on the Controller to the AXlink connector at the rear of the AXB-TPI/3. This is the only method of programming the interface unit using Send_Commands. Included Accessories • Two rack-mount ears and a package of rack screws • One 4-pin AXlink connector • One 2-pin P

When done, complete the insertion of the remaining housing latches. 4. Verify that the notches along the bottom of the plastic battery slot separator strip also fit into the three provided alignment holes on the circuit board. 5. Firmly press down around the entire rim of the outer housing to snap the cover back into place. Be careful not to pinch the antenna wire in the housing. 6. Use a grounded Phillips-head screwdriver to insert and re-secure the two housing screws removed in Step 1. 7. Inse

BECAUSE SOME STATES/COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT APPLY TO LICENSEE. • U.S. GOVERNMENT RESTRICTED RIGHTS. The AMX Software is provided with RESTRICTED RIGHTS. Use, duplication, or disclosure by the Government is subject to restrictions as set forth in subparagraph ©(1)(ii) of The Rights in Technical Data and Computer Software clause at DFARS 252.227-7013 or subparagraphs ©(1) and (2) of the C

Any implied warranties on the SOFTWARE and hardware are limited to ninety (90) days and one (1) year, respectively. Some states/countries do not allow limitations on duration of an implied warranty, so the above limitation may not apply to you. CUSTOMER REMEDIES. AMX Corporation’s entire liability and your exclusive remedy shall be, at AMX Corporation's option, either (a) return of the price paid, or (b) repair or replacement of the SOFTWARE that does not meet AMX Corporation's Limited Warranty

•Disk drive mechanisms, pan/tilt heads, power supplies, and MX Series products are warranted for a period of one (1) year. •AMX lighting products are guaranteed to switch on and off any load that is properly connected to our lighting products, as long as the AMX lighting products are under warranty. AMX also guarantees the control of dimmable loads that are properly connected to our lighting products. The dimming performance or quality there of is not guaranteed, impart due to the random combina

23 DHCP............................................................................................................................ 23 Configuring Wireless Network Access (MVP-5150 Only)........................................ 23 Step 1: Configure the Device's Wireless IP Settings (MVP-5150 Only)................... 23 Wireless communication using a DHCP Address........................................................... 24 Wireless communication using a Static IP Address.....................

• SSH, HTTPS, and program terminal session timeouts are enabled. • ICSP communication protocol between devices: encryption and authentication are enabled. • Minimum password requirement is 8 characters with at least 1 numeric character. • Login failure attempt pauses 4 seconds before another login attempt is allowed. • After 3 consecutive unsuccessful login attempts, login lockout is enabled for 15 minutes. • Login and logout audit logging is enabled. VG-Series Modero Touch Panels Firmware Pages

Refer to the NetLinx Master instruction manual for more detailed information on the use of the new Web-based NetLinx Security. 1. Press and hold the two lower buttons on both sides of the display for 3 seconds to open the Setup page. 2. Press the Protected Setup button (located on the lower-left of the panel page) to open the Protected Setup page and display an on-screen keypad. 3. Enter the appropriate password into the Keypad’s password field (1988 is the default password with a new unit) a