valutazioni - 2, GPA: 4
(
)
)
|
Facilità d'uso
5-6), be sure to observe the following order when switching on the power to your equipment. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. When powering up: Turn on the power to your guitar amp (or the like) last. When powering down: Turn off the power to your guitar amp (or the like) first. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. * When operating on battery power only, the unit's indicator will become dim when battery poiuer gets too low. Replace the battery as soon as possible. Connecting to Normal Input on the Guitar/Bass Amp Guitar Amplifier Bass Amplifier 5 Making the Connections Connecting to SEND/RETURN on the Guitar Amp The unit's equalization effects are obtained after the preamp. * Match the send output level on the guitar amp and the level setting on the unit. If the PEAK indicator lights up frequently, turn down the output on the guitar amp. * When the guitar amp's SEND/RETURN pedal is at +4 dBu, set the LEVEL szvitch on the rear panel of the unit to +4 dBu. Connecting to an MTR or Mixer 6 Operation When you switch on the power, the unit is set to the state it was in when the power was last switched off (MANUAL/MEMORY, Memory Number). Pedal Operation This lights up when set to "MANUAL." Each press of the EFFECT ON/OFF pedal switches effects on or off. When effects are off, the sound coming in through the INPUT jack is output unchanged. Each press of the MANUAL/ MEMORY pedal switches the unit between "MANUAL" and "MEMORY." 7 Operation Panel Operation When Set to "MANUAL' Equalizer Sliders The sliders (30, 60,120,200, 400, 800,1.6 k, 3.2 k, 6.4 k, and 12.8 k [Hz]) adjust the sound quality. LEVEL Slider This corrects differences in level when effects are on or off. PEAK Indicator If the PEAK indicator lights up frequently, switch the LEVEL switch on the rear panel of the unit. GUITAR/ BASS — GUITAR AMP - SEND/RETURN J (+4dBu) 3BOS5 Before you operate the LEVEL switch, be sure to turn down the volume on all equipment to prevent malfunction or speaker damage. A When set to MANUAL, the backlit does not light up even when the I)TOp|: equalizer sliders, the LEVEL slider, or the EFFECT ON/OFF pedal are operated. 8 Operation When Set to "MEMORY" SELECT Button Pressed to select a memory location (1 through 9). Holding down the button makes the memory number change automatically. When the unit is shipped from the factory, equalization settings are stored in memories 1 through 9. For information about the settings, refer to "Factory Default Settings" (p. 17). 9 Operation Storing Settings (Write Operation) A, Even when you carry out a write operation while the MEMORY indicator is lighted NOTE ("MEMORY"), settings made for "MANUAL" are not stored. Be sure to carry out such operations when the MANUAL indicator is lighted (in the "MANUAL" mode). Do not switch off the power while a write operation is in progress. 1. While at "MANUAL," adjust the equalizer sliders and the level slider to obtain the desired equalization. Illuminated 2. Press the LIGHT button and the SELECT button at the same time. The text "WRITE SURE?" flashes in the display, and the unit enters write standby. * To cancel the write operation, press the MANUAL/MEMORY pedal. 10 Operation 3. Press the SELECT button to choose the number of the memory 0 through 9) to store the settings. To avoid deleting previously stored settings, check the display before Smb. »mi overwriting. 4. Again press the LIGHT button and the SELECT button at the same time. "OK" appears in the display and the write operation finishes. (’o'iEQ-aQ sa«PHicequalizer_A.uv;inci:» EQ(o' * From step 2 and after, you cannot adjust the sound quality or volume level by moving the sliders. * If you want to change what is in memory, refer to ‘'Changing What Is in Memory Before Storing" (p. 12). * If you want to return the settings to the factory defaults, refer to "Returning Settings to Their Factory Defaults" (p. 16). 11 Operation Changing What Is in Memory Before Storing Do not switch off the power while a write operation is in progress. 1. Press the MANUAL/MEMORY pedal to change to the "MEMORY." 2. Press the SELECT button to choose the number of the memory you want to change. * Holding down the SELECT button makes the memory number change automatically. (o'j EQ-20 GRAPHIC EQUALIZER_NCEI? EQ iO} 3. Operate the equalizer slitiers or the level slider to change the equalization. The display shows the positions of the sliders stored in memory. When you operate the sliders, the present positions (settings) flash until they match the setup stored in memory. 12 Operation Flashing 4. 5. 6. HINT The unit enters a state where you can make changes from when...