valutazioni - 3, GPA: 4.7
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
If a password has been set for Administrator, set the password again. Updating the EtherSound module firmware (M7CL-48ES) For more information on the ES-Firmware Updater, the EtherSound firmware update program, visit the AuviTran SARL website or refer to the .ES-Firmware Updater USER.S MANUAL. installed during the course of this update. 1. Turn off the power to the M7CL -48ES. 2. Double-click .AVS-FirmwareUpdater Setup vx.xx.exe. (the update program installer you downloaded from the AuviTran website), then follow the instructions on screen to install the program. “vx.xx. represents the version number of the ES-Firmware Updater. NOTE .When running under Windows Vista / Windows 7, the "User Account Control" dialog box may appear. Click [Continue] or [Yes]. .You may be prompted to restart the computer after the installation is complete. Before proceeding to step 3, restart the computer. 3. Connect the EtherSound [IN] jack on the rear panel of the M7CL-48ES unit to the Ethernet jack on the computer using an Ethernet cable. 4. Turn on the power to the M7CL -48ES. 5. Select [Start]>[All programs]>[AuviTran]>[Firmware Update]>[ES-Firmware Updater]. A license agreement dialog box will appear. NOTE .When running under Windows Vista / Windows 7, the "User Account Control" dialog box may appear. Click [Continue] or [Yes]. 6. Scroll to the end of the agreement, then click [I Agree]. The ES-Firmware Updater will start up. NOTE .If a dialog box enabling you to stop the EtherSound service appears, click [Yes]. 7. For [Network adapter] in the .Settings. section, select the network adapter for the Ethernet connector that is connected to the M7CL-48ES. 8. Check the box to the left of the device description listed in the .EtherSound Devices. section. NOTE .If no device is listed, click the [Refresh] button. If still no device is listed, your computer may not be properly connected to the M7CL-48ES.Please make sure that the cable is not disconnected or damaged, that you have selected the correct network adapter, and that the M7CL-48ES has started in Normal mode. 9. Select an appropriate firmware component for [Firmware to program:] in the .Program. section. Select firmware version 0x0C18 or later. 10. Click the [PROGRAM] button in the .Program. section. The update operation will begin. The update will take about 3 minutes. During the update operation, do not turn off the power to the unit or disconnect the cable. If update fails due to disconnection of the power cable during the update, or due to other reasons, the device may become inoperative. 11. When a .Success!. dialog box appears, click [OK]. The update is now complete. If a dialog box other than .Success!. appears, first make sure that the devices are connected properly, then close the ES-Firmware Updater without turning off the power to the M7CL-48ES. Then, resume the procedure from step 5. 12. Restart the M7CL-48ES. 13. Click the [Refresh] button in the .Settings. section. The .EtherSound Devices. section will display information on the M7CL-48ES that you just restarted. 14. Make sure that the firmware version displayed in the .EtherSound Devices. section matches the firmware version to which you just updated. If the version numbers do not match, the update operation may have failed. Try the update operation again, starting from step 8. 15. Click [Exit]. The ES-Firmware Updater will close. The EtherSound module firmware update is now complete. Yamaha Corporation, All Rights Reserved. © 2009-2011 Yamaha Corporation E0 ...
Questo manuale è adatto anche per i modelli :Strumenti Musicali - M7CL-32 (260.14 kb)
Strumenti Musicali - M7CL-48 (260.14 kb)