Without accessory economizer — Upon a request for cooling from the space thermostat, terminals Y1 and G will be energized with 24 v. As a result, the indoor-fan contactor (IFC), outdoor-fan contactor (OFC) and Compressor contactor no. 1 (C1) will be energized, which in turn will energize the indoor fan, outdoor fan and Compressor no. 1, respectively. If the space thermostat calls for a second stage of cooling by supplying 24 v to Y2, Compressor contactor no. 2 (C2) will be energized, thus energi

1 - Typical 2 Cylinder Water-Cooled Condensing Unit (07DA102, Single-Phase Illustrated) Carrier INSTALLATION 06D,07D DISCHARGE , DISCHARGE MANIFOLD DISCHARGE MUFFLER GAGE CONN.~~----.--_ / PRESSURESTAT CONN.__„ TERMINAL BLOCK SUCTION PRESSURESTAT CONNECTION-—-S COMPRESSOR NAMEPLATE suction shut-off ^run valve capacitors SUCTION GAGE TART C0NN APACITORS PUMP END BEARING HEAD OIL PUMP COVER BULL'S EYE - m OIL DRAIN PLUG- WATER OUTLET . ................................................

For medium temperature (R-134a) applications, an 06EM compressor is standard. Factory substitutions may be made. Contact Carrier Sales Representative. †The condenser listed is for R-22, air conditioning duty and may change based on the application. Maximum condenser operating pressure: 350 psi refrigerant side, 150 psi water side. START-UP Energize crankcase heater at least 24 hours prior to start-up. Check to see that oil level is approximately 1/3 up on the compressor sight glass. Open water s

SWITCH —o- SAFETY DEVICE CONTACTS,N.C Ï_1 "m'Iaux ■* TCONTACTS,NOJ •—#—J PUMPOUT RELAY p POR CONTACTS.NO. TR TR CONTACTS,N.O. -#- a2 LIQ SOL VALVE A|o_ a a a ■o —I I HIGH PRESS SWITCH TIMER RELAY B2 ! COND AUX AUX CONTACTS,N.O. —°—s|f—Ç) COMPRESSOR CONTACTS.N.O. 1. Starting Sequence (Assuming evaporator interlocks and all operating safety controls are in closed position) Time: 0 Min 0 Sec - Timer switch plunger is up at beginning edge of cam node and contacts are in po

In this position, set point is 86 psig. Control set point is then regulated to desired pressure by turning adjustment nut counterclockwise. Each full turn decreases set point by approximately 7.2 psi. Approximately 12 turns counterclockwise lowers the control set point to 0 psig. See Table 5. Table 5 — Capacity Control UNIT 06E,07E NO. OF CONTR % Full Load Capacity 100 67 49 32 % Full Load kW CYL 100 73 57 46 Number of Active Cylinders ALL 4 CYLINDER MODELS 2 4 — 2 — ALL 6 CYLINDER MODELS 4 6 4

If phasing is correct, circuit R-Y energizes contactor, starting outdoor-fan motor and compressor circuit. R-G energizes indoor unit-blower relay, starting indoor-blower motor on high speed. NOTE: If the phasing is incorrect, the contactor will not be energized. To correct the phasing, interchange any 2 of the 3 power connections on the field side. When thermostat is satisfied, its contacts open, de-energizing the contactor and blower relay. Compressor and motors should stop. NOTE: If indoor uni

NOTE: Ratings contained in this document are subject to change at any time. Always refer to the AHRI directory (for the most up- --to- --date ratings information. INDUSTRY LEADING FEATURES / BENEFITS Efficiency S 13 SEER/ 10.8 - -- 11.0 EER / 8.0 - -- 8.4 HSPF (nominal) S Microtube Technologyt refrigeration system S Indoor air quality accessories available Sound S Sound level as low as 71 dBA S Compressor sound blanket Comfort S System supports Thermidistatt or standard thermostat controls Relia

1 - Typical Automatic Water Strainer Installation UNIT DESCRIPTION The 29D Automatic Water Strainer cleans foreign matter from the return water of a Rotaspray® system. Figure 1 shows a typical installation. OPERATING CYCLE Water enters the open end of the strainer drum and passes outward thru the perforated skin. Foreign matter is screened out of the water, and covers the inside surface of the drum causing the water level to rise on the dirty side of the tank. The water level on the clean si

1-7 Step 1 — Check Equipment and Jobsite . I • UNPACKAGE UNIT • INSPECT EQUIPMENT • COMPLETE OR CONSIDER SYSTEM REQUIREMENTS Step 2 — Mount Outdoor Heat Pump .. 3 • ON THE GROUND: MOUNT UNIT ON A SOLID, LEVEL CONCRETE PAD • ON THE ROOF: MOUNT UNIT ON A LEVEL PLATFORM OR FRAME Step 3 — Make Piping Connections____ 3-5 • REPLACE THE ACCURATER™ REFRIGERANT CONTROL PISTON IN THE INDOOR COIL AS REQUIRED • CONNECT REFRIGERANT LINES Step 4 — Make Electrical Connections .. 5-7 • INSTALL A BRAN

2{°pens (F) 012 890 500 _36 Recip Hermetic; 06DA337 6 10 „ 75 _ Propel 1er 2 1 120 22 % Plate 016 ~oi oses (F) lens (F) oses (F) 5 15_ 65+3 45 ± 3 272 178 60 65 70 75 57 62 *Approximate charge with 25 feet of interconnecting piping Use appropriate charging charts for actual charging of unit tRefrigerant sto