Log:
Scaricare : 1   File Size : 224 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

There are four screws holding each lens in place. 2. Remove the light bulbs. 3. Now is a good time to clean the lenses and housings. If lenses are in bad shape a new set is recommended. 4. DO NOT remove the tape from the LED assemblies yet! MAN#650203 5. Test fit the assembly into the tail light housing as shown below to make sure it aligns correctly. 6. Before mounting the new LED assembly into the housing, plug the bulb base into the stock bulb socket and test the tail lights and flasher

Scaricare : 3   File Size : 222 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

B Kit Includes: m, m Installation: 1. Remove the screws and the tail light lens. 2. Remove the tail light bulb. 3. Now is a good time to clean or replace the lens and housing if necessary. 4. The new LED assembly will mount into the original light bulb socket. Push it into the socket and turn it clockwise to lock it in. 5. Repeat for the other tail light. 6. Test the tail lights, brake lights, and turn signals. If the turn signals do not flash, you will need to upgrade your flasher. If

Scaricare : 3   File Size : 215 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside of the housing.The flat side of the mounting disk should betoward the outsideand thes

Scaricare : 1   File Size : 202 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

4. Remove the tail light lens. 5. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 6. Remove the lock nuts and aluminum back plate from the back of the new LED assembly. 7.Insert the new LED assembly through the hole where the original bulb and connector were. Use caution when feeding the wires through to avoid damaging the wire insulation. 8.Feed the wires through the large hole in the back plate and attach the back plate onto the backside o

Scaricare : 2   File Size : 199 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

Remove the tail light lens. 2. Remove the light bulb. 3. Remove the original bulb connector from the back side of the housing. The housing may need to be removed from the car on the ’71-’72 Chevelle. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the screw and aluminum back plate from the back of the new LED assembly. LED assembly standard back back for ‘71-‘72 Chevelle (attached to the assembly) (packaged separately) 6. Insert

Scaricare : 0   File Size : 182 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

Remove the original bulb connectors from the bottom side of the housing. 2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Note that the screws and mounting plates are assembled differently for the driver side set and passenger side set. The LED assemblies will sit in the housing at an angle similar to the b

Scaricare : 2   File Size : 177 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

Remove the tail light housing from the vehicle. 2. Remove the bulb connector from the back of the housing. 3. Remove the 4 screws that hold the trim and lens. Remove the trim and tail light lens from the tail light housing. 4. Now is a good time to clean or replace the lens and housing if necessary. 5. Note that there are two different LED assemblies. One for the driver side and one for the passenger side. Select the correct assembly for the tail light housing. Remove the two locking nuts and fl

Scaricare : 5   File Size : 168 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

Remove the tail light assembly from the vehicle by removing the original bulb sockets from the housing. Then remove the housing hardware so it can be removed from the car. Remove the housings from the vehicle carefully so the housing to body gaskets are not damaged. 2. Next remove the lens. The 67-68 Camaro has six screws that hold the housing halves together which will need to be removed to gain access to lens. The 70-73 Camaro lens has tabs locking it into the plastic housing. Pry the tabs gen

Scaricare : 1   File Size : 159 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

There are four screws holding each lens in. 2. Remove the tail light bulbs. 3. We recommended that the lens and housings be cleaned to insure proper mounting and visibility of the LED assembly. If the lenses are in bad shape a new set is suggested. 4. DO NOT remove the tape from the led assemblies yet! 5. Test fit the assembly into the lens as shown below to make sure it aligns correctly. 6. Make sure you have BOTH lenses clean and dry so the single use primer applicator can be used for bot

Scaricare : 3   File Size : 157 kb   Produttore : Dakota Digital  
Categoria : Illuminazione
@name

2. Remove the plastic housing from the vehicle. 3. Remove the tail light lens by gently prying the housing away from the lens tabs. 4. Now is a good time to clean the lens and housing. If lenses are in bad shape a new set is recommended. 5. Remove the round mounting plate from the bottom of the LED assembly. It is attached with two lock nuts. 6. Insert each new LED assembly through the hole where the original bulb and connector were located. Use caution when feeding the wires through the socket





categorie