This will only last a few hours. LIGHTING INSTRUCTIONS 1. STOP! Read the safety information above. 2. Make sure equipment shutoff valve is fully open. 3. Press in and turn control knob clockwise to the OFF position. 4. Wait five (5) minutes to clear out any gas. Then smell for 5. Slightly depress and turn control knob counterclockwise to the PILOT position. Keep control knob pressed in for five (5) seconds (see Figure 31).Note:You may be running this heater for the first time after hooking up to

5. Install one plastic bushing provided in blower kit into the 1 1/2" hole in the left rear of firebox floor. Access hole through the rectangular opening in the rear panel (see Figure 15). 6. Remove the two blower mounting brackets from the rear panel by removing two screws each (see Figure 16, page 13). 7. Attach the two mounting brackets to blower housing using four screws provided in blower kit (2 for each bracket) (see Figure 16, page 13). Tighten screws securely. Place blower assembly tempo

WARNING: Make sure the selector switch is in the OFF position when you are away from home for long periods of time. Heater will come on automatically with selector switch in the ON position. Pilot Burner Ignitor Electrode Figure 25 - Pilot No Control Options) 14 104461 Remote Selector Switch in Remote Position (Optional Remote Control) ON OFF REMOTE OFF PILOT ON LO IH ON OFF REMOTE OFF PILOT ON LO IH OWNER’S MANUAL OPERATING HEATER Continued TO TURN OFF GAS TO APPLIANCE Shutting Off Heater 1. Tu

Ventilation Air From Outdoors Provide extra fresh air by using ventilation grills or ducts. You must provide two permanent openings: one within 12" of the ceiling and one within 12" of the floor. Connect these items directly to the outdoors or spaces open to the outdoors. These spaces include attics and crawl spaces. Follow the National Fuel Gas Code, ANSI Z223.1/ NFPA 54, Section 5.3, Air for Combustion and Ventilation for required size of ventilation grills or ducts. IMPORTANT: Do not provide

If the fire is on it will be turned off automatically. In the locked state, the light will not light up when any button is pressed. TO UNLOCK press both buttons together on hand-held remote control until the light stops flashing. The hand-held remote is now un locked. Control Button Turns Burners On and Off Figure 23 - On/Off Hand-Held Remote Control Unit (GHRCB) THERMOSTAT SERIES (MODEL GHRCTB) The hand-held remote can be operated using either the manual mode (MANU) or thermostatic mode (AUTO)

Check your local codes. Use pipe of 1/2" diameter or greater to allow proper gas volume to heater. If pipe is too small, undue loss of volume will occur. Installation must include an equipment shutoff valve, union, and plugged 1/8" NPT tap. Locate NPT tap within reach for test gauge hook up. NPT tap must be upstream from heater (see Figure 8, page 9). IMPORTANT: Install equipment shutoff valve in an accessible location. The equipment shutoff valve is for turning on or shutting off the gas to the

This will only last a few hours. 1. STOP! Read the safety information, above. 2. Make sure equipment shutoff valve is fully open. 3. Turn control knob clockwise to the OFF position. 4. Wait five (5) minutes to clear out any gas. Then smell for gas, including near the floor. If you smell gas, STOP! Follow “B” in the safety information, column 1. If you don’t smell gas, go to the next step. 5. Turn control knob counterclockwise to the PILOT position. Press in control knob for five (5) seconds (see

Make sure middle section at bottom of log is seated into "U" shaped cutout in center of heater base. Log will fit securely on base. IMPORTANT: Make sure log does not cover any burner ports and does not touch the stove cavity (see Figure 13). 5. Fasten back panel to stove with four (4) M6 x 1bolts and washers. 6. Place freestanding stove in desired position in room. Be sure to maintain clearances to combustibles as outlined on page 8. CAUTION: After installation and periodically thereafter, check

This is common with most heaters. If just after burner is lit or shut off tracting while cooling noise is excessive, contact qualified service person Heater produces unwanted odors 1. Heater burning vapors from paint, hair 1. Open window and ventilate room. Stop spray, glues, cleaners, chemicals, new using odor causing products while heater carpet, etc. (See IMPORTANT state-is running ment above) 2. Gas leak. See Warning statement at 2. Locate and correct all leaks (see Check- top of page ing Ga

See Lighting Instructionson page 14. 1. After lighting, let pilot flame burn for about one minute. Turn control knob to ON position. Adjust flame adjustment knob anywhere between HI and LO. Slide the remote selector switch to the REMOTE position. Note:The burners may light if handheld remote ON button was on when remote selector switch was last turned off. You can now turn the burners on and off with the handheld remote control unit. IMPORTANT: Do not leave the remote selector switch in the REMO