This side explains the setup procedure for use by connecting to a computer. You can use the copy, photo print (MP370) functions. You can use the print, scan functions. Connect power cord Install Utility Software Install print head Install MP Drivers Install ink tanks Connect USB cable Unpack and install Load print media Align print head the machine Unpack and install the machine. 1 Carefully remove all items from the box. NOTE • When removing the machine from the box, take sufficient care not to drop it. 2 Remove the protective material. NOTE • After removing the protective material, do not lift the machine by grasping the scan unit. Hold the bottom side. 3 Place the machine on a flat surface. • Be sure to hold the machine by the sides. Set nothing in front of the machine. 4 Remove all shipping tape from the exterior of the machine. • After removing the tape, remove the protective sheet. Do not grasp the scan unit. HT3-2142-000-V.1.0 NOTE • In this sheet, illustrations of MP370 are shown. • A printer cable is not included.You must purchase a USB cable (less than 16 3/8 ft./5 m) to connect your machine to a computer. • MP370 • MP360 • Print head • Ink tanks BCI-24 Black BCI-24 Color • Power cord • Set-Up Sheet • User's Guide • Setup CD-ROM The Setup CD-ROM contains the MP Drivers, as well as the electronic manuals Software Guide and Photo Application Guide. Please read these guides. Check the contents. Connect the power cord. 1 Connect the power cord. If the message appears, go to procedure 3, "Install the print head." Approx. 15 seconds Install the print head. 1 Lift the scan unit until it locks into place. • If a protective sheet is on the inner side of the scan unit, remove the protective sheet. NOTE • If you open the scan unit while the machine is turned ON, the paper output tray will open. Click Lift the scan unit. q Open the inner cover. 2 Open the inner cover. 3 Raise the lock lever. Touch only here! Raise this securely. Remove the protective cap and dispose of it. Do not touch! 5 Insert the print head. 6 Lower the lock lever. Click Lower the lock lever until it locks into place. 4 Prepare the print head. If the paper output tray does not open, press the Open button to open the paper output tray. w The print head holder moves to the center. Install here. 2 Load the print media. 3 Pull out the tray extension of the paper output tray. Install the ink tanks. 1 Prepare the ink tanks. 2 Insert the ink tanks. Remove the protective cap and dispose of it. Black Do not touch! Click Insert the black ink tank into the right slot. Push it in until it locks into place. Insert the color ink tank into the left slot. 3 Close the inner cover qand the scan unit w. Click q Swing it upward into place. w Lower it into place. Load the print media. 1 Open the multi-purpose tray. w Pull up the tray extension until it stops. Incorrectly installed Correctly installed Rear side a NOTE Pull it out until it stops. q Load the print media with the print side face up. w Pinch and adjust the paper guide to the width of the stack. Ensure the paper stack does not exceed paper limit mark. q Open the tray. Align the print head from the operation panel. Be sure to align the position of the print head to ensure quality printing. 1 Print the print head position pattern. 2 Enter checkmarks in the printed patterns. • From column A to column K on the printout, enter checkmarks in the patterns that have the most solid image. 3 Align the print head. • In column A on the printout, select the pattern that you checked on the printout in step 2, then press [Set]. 4 Repeat step 3 for columns B to K. w Press [Set]. If this message does not appear after closing the scan unit, see page 86 of the User's Guide. Column A GOOD SAMPLE BAD SAMPLE Least solid box Most solid box q Press [+] or [-] to select the pattern number of the good sample. w Press [Set]. Press [+] to increase the number one digit. Press [–] to decrease the number one digit. You have completed installation and alignment. If you are connecting the machine to a computer for use, see , and for instructions on installing the software. eThe machine prints a print head position pattern. Columns (A to E) Pattern numbers Columns (F to K) qThis message appears. Install the MP Drivers. The MP Drivers must be installed on the hard disk of your computer in order to print from or scan images to the computer. In addition to installing the MP Drivers, install the MP Toolbox. Use the MP Toolbox to attach scanned images to e-mail and store them. IMPORTANT • For detailed system requirements, see page 64 of the User's Guide. • When installing the software in Windows 2000, you must have Service Pack 1 or later version installed. • When installing the software in Windows 2000, you must log on as Administrator or have Administrator privileges. • When installing the software in Windows XP, you must lo...
)
Log: