valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
These characters are available in fonts 1–6 and 9. Getting Started 13 _______________________________________________________________________ 14 Getting Started 2.4 Memory Cartridges The Printer has one standard memory cartridge slot. The primary use of the memory cartridges is for storing label formats, graphic images, fonts and for internal batch. Follow the instructions outlined below when installing memory cartridges. 1. Ensure that all printing has been completed. 2. Open the Side Access Cover. 3. Plug the Memory Cartridge into the Memory Cartridge Slot with the label face-up. Figure 2-3 Installation of a Memory Cartridge NOTE: Use only memory cartridges designed specifically for your Printer, flash modules have a Write Protect Switch. _______________________________________________________________________ Getting Started 15 2.5 Media Loading The Printer supports up to an 8" (203mm) diameter roll of media, (if media less than 4 inches wide is used, refer to Section 5.3.1 before loading media). Follow the instructions outlined below when installing the media stock. 1. Open the Printer's Side Access Cover. 2. Rotate the Printhead Latch (1) counterclockwise to unlatch and raise the Printhead to an upright position. 3. Lower the Hinge Plate (2). 4. Slide the Media Edge Guide (3) to the outer edge and rotate it to the down position. Figure 2-4 Media Access _______________________________________________________________________ 16 Getting Started NOTE: If using fanfold media, skip steps 5 and 6. Install fanfold media as shown in figure 2-5b. 5. Place the 3" Media Core Adapters on the Media Hub Assembly, (if using media with 3" media cores). Figure 2-5a Media Installation (3" core) 6. Place the Media Supply Roll on the Media Hub Assembly. Slide the media retainer against the supply roll and tighten the thumb screw. NOTE: Do not use the media retainer if the Media Supply Roll is wider than 4 inches (102mm). _______________________________________________________________________ Getting Started 17 7. Route the media over the Guide Plate, between the Media Sensor, and over the Platen Roller, (located beneath the Printhead), as shown in Figure 2-5b. 8. Rotate the Media Edge Guide up and slide it to the media's edge. 9. Close the Hinge Plate and lower the Printhead by rotating the Printhead Latch clockwise to the latched position. Figure 2-5b Media Installation NOTE: If the media is not sensing, try adjusting the Media Edge Sensor by turning the Media Edge Sensor Adjustment knob (see Section 5.3.2). _______________________________________________________________________ 18 Getting Started 2.5.1 Using the Optional Internal Rewind If the Internal Rewind Option is installed in your Printer, then the media and Arc Plate should be installed as described below. NOTE: The Arc Plate is supplied only with the Internal Rewind Option. 1. Turn off the Printer and open the Side Access Cover. 2. Follow steps 2, 3, and 4 of Section 2.5 before installing media. 3. Open the Lower Right Front Panel. 4. Remove the Arc Plate from its stored position and install it on the front of the Printer as shown in Figure 2-6. Figure 2-6 Installing the Arc Plate for Internal rewind 5. Place the media core adapters on the Media Hub Assembly if using 3" cores, (see Figure 2-5a). _______________________________________________________________________ Getting Started 19 6. Place the Media Supply Roll on the Media Hub Assembly. Slide the media retainer against the Media Supply Roll and tighten the thumb screw. NOTE: Do not use the media retainer if the media is wider than 4" (102 mm). 7. Route the media over the Guide Plate, between the Media Sensor, and over the Platen Roller, (located beneath the Printhead), around the Arc Plate and to the Media Rewinder as shown Figure 2-7. 8. Place the Clasp over the end of the media and rotate the Media Rewinder a few turns. 9. Rotate the Media Edge Guide up and slide it to the media's edge. 10. Close the Hinge Plate and latch the Printhead by rotating the Printhead Latch upward to the latched position. Close the side cover. Figure 2-7 Installing Media with Internal Rewind Option _______________________________________________________________________ 20 Getting Started 2.5.2 Using the Peel and Present Option The Peel and Present Option allows for on-demand label dispensing and requires the Internal Rewind Option. To use this option follow the instructions outlined below. 1. Turn off the Printer and open the Side Access Cover. 2. Follow steps 2, 3, and 4 of Section 2.5 before installing media. 3. Open the Lower Front Panel. 4. Using a phillips screw driver, remove the Tear Bar, invert it (flip it over), and re-install it as shown in Figure 2-8. Figure 2-8 Using the Peel and Present Option NOTE: If media narrower than 4 inches is used, refer to Section 5.3.1 before loading media. _______________________________________________________________________ Getting Started 21 5. Place the Media Supply Roll on the Media H...
Questo manuale è adatto anche per i modelli :Stampanti - 2034 (3.95 mb)