i / 2 Connect the power supply cord. Connectez le cordon d’alimentation. 4 Raise the paper support and extend the paper exit tray. Levez le support papier et tirez le bac de sortie. 5 Lift the scanner unit. Soulevez l'unité du scanner. 6 Remove the sticker and tape from the print cartridge(s). Retirez l’autocollant et la bande protectrice des cartouches. 7 Insert the cartridge(s) and snap the lid(s) closed. Insérez les cartouches, puis fermez les couvercles d'un coup sec. .2, 21T

For more information, see the Card Stock & Label Guid available on the Lexmark Web site av • Do not load too much paper. Make sure the stack height does not exceed the indicated maximum height. •Do not load wrinkled, creased, damp, or curled paper. • Flex, fan, and straighten paper before loading it. •Do not use paper that has been cut or trimmed by hand. •Do not mix paper sizes, weights, or types in the same stack. • Store the paper in an appropriate environment. • Do not remove trays while the

Off resets the printer to itu factory default settings0 • The Energy setting minimizes the power used by the printer0 Performance may be affected but quality is not0 • Paper minimizes the amount of paper and specialty medi< needed for a print job. Performance may be affected buO quality is not0 • Energy/Paper minimizes the use of power and of paper anf specialty media0 Quiet Mode Reduces the amount of noise produced by the printet Ofh Notes: OI • Off is the factory default setting0 • On configur

Available settings range from 1–240 minutes0 8 Pressu 0 Submitting changes appears0 9 Pressu , and then pressu until Ready appears0 Note: Power Saver settings can also be adjusted by typing the printer IP address into the address field of your We= browser0 Minimizing your printer's environmental impact 46 Recycling Lexmark provides collection programs and environmentally progressive approaches to recycling. For mor@ information, see< • The Notices chaptet • The Environmental Sustainability secti

Off Auto Configuration Specifies whether the network adapter accepts the automatic IPv6 address configuration entries provided by a router Off On Note: On is the factory default setting. View Hostname Lets you view the current setting Note: These settings can be changed only from the Embedded Web View Address Server. View Router Address Enable DHCPv6 Enables DHCPv6 in the printer On Note: On is the factory default setting. Off Wireless menu Use the following menu items to view or configure the w

By doing so, ink will flow out of the nozzles and has to be dabbed away immediately with a tissue. This trick allows pressing sealed air bubbles out of the nozzle chamber. Should the cartridge print in streaks, please start a cleaning cycle with your printer software. If the problem remains, dab the nozzles with a dampened cloth or leave them to settle in warm water for few minutes. You are facing difficulties refilling your ink cartridges or require more information about the refilling proced

Use of a substitute cable not properly shielded and grounded may result in a violation of FC regulations0 Noticeq 235 Any questions regarding this compliance information statement should be directed to< Director of Lexmark Technology & Serviceu Lexmark International, Inc0 740 West New Circle Roaf Lexington, KY 40552 (859) 232–3002 Modular component notice Wireless-equipped models contain the following modular component(s)< Lexmark Regulatory Type/Model LEX-M04-001, FCC ID: IYLLEXM04001; IC:2376A

Use of controls or adjustments or performance oh procedures other than those specified herein may result in hazardous radiation exposure0 This product uses a printing process that heats the print media, and the heat may cause the media to release emissions0 You must understand the section in your operating instructions that discusses the guidelines for selecting print medi< to avoid the possibility of harmful emissions0 CAUTION—HOT SURFACE: The inside of the printer might be hot. To reduce the r

X54x Series User's Guide August 2009 Machine type< 752 Model numbers< 131, 133, 138, 332, 333, 336, 337, 352, 356, 382, 383, 386, 389 ContentsCContentsC Safety information...........................................................................11 Learning about the printer.............................................................13CFinding information about the printer........................................................................................................................15 S

(fig.2) 2. Remove the top from the black ink bottle and using the syringe remove 5ml of the colour ink (fig.3) 3. The lid has to be removed from the cartridge. Cut around the edge with a sharp knife and then remove (fig.4) 4. Insert the steel filling tube into the appropriate filling holes. (fig.5). Push down into centre of the sponge. IMPORTANT: Cartridge contains a sponge and a slight resistant may be felt. 5. SLOWLY Inject ink. Stop filling before ink overflows as you do not want the ink