valutazioni - 3, GPA: 4 ( )

Produttore : Southbend File Size : 1.52 mb File Nome : Lingua di insegnamento:

12. Place the appliance on top of the stand, making sure that the angle brackets that you just installed on the bottom of the appliance are inserted into the front and rear top supports. No additional bolts or screws are required. Lift the appliance only at the ends, never in the middle! 13. Go on to Step 4 on page 18. PAGE 14 OWNER’S MANUAL 1182845 REV 8 HEAVY DUTY COUNTERLINE INSTALLATION Step 2e: Installation on Floor Stand (60" and 72" Models) A 60" or 72" griddle may be installed on top of an optional floor stand (for 24", 36", and 48" griddles, go to Step 2d on page 13). The floor stand is shipped in a separate crate and must be assembled, as follows: 1. Position the bottom-brace pieces on a flat surface, as shown in Figure 10 below. There are four bottom-side braces (items “A”), and four front/rear bottom-braces (items “B”). 2. Position a corner brace (item “C”) in each interior corner, matching the pre-punched holes on the lower inside flange of the bottom braces. 3. Position the six leg brackets (item “D”); one in each corner of the stand, one front-center, and one rear- center, as shown in Figure 10. Be sure that the bracket flanges are engaged into the open hem of the bottom braces. 4. Use the thirty-two 1/2"-long hex head bolts (items “E”), lock washers (items “F”), and acorn nuts (items “G”) to bolt the corner braces to the bottom braces. Only hand-tighten for now. 5. Check that the leg brackets are in the proper position, and that the outside corners are square. Figure 10 A B D C A A B B DD D C C C C E C A E G F B 6. Use the twelve 1-1/2" hex bolts (items “H” in Figure 11) to attach the two left-legs (items “I”), the two right-legs (items “J”), and the two center-legs (items “P”). “Left” and “right” are as seen from the front or rear of the stand. Be sure that the small threaded-insert near the top of each leg faces either the front or the rear of the stand, not a side. Insert the bolts through the leg brackets and into the legs. Only hand-tighten the bolts for now. INSTALLATION OWNER’S MANUAL 1182845 REV 8 PAGE 15 INSTALLATION HEAVY DUTY COUNTERLINE Figure 11 INSTALLATION N O M K K L L J I PI J H H P 7. Check the partially assembled stand to make sure that the legs are straight and that all corners are square. Now tighten all bolts, but do not over tighten. 8. If legs with casters were ordered, lift the stand and screw the caster assemblies into the bottom of the legs. The two casters with wheel-locks go on the front corner legs. After the stand is assembled, connect the required restraint to protect the flexible gas connection (see Step 3 on page 17). 9. If the optional shelves were ordered (items “K”), position them on top of the bottom braces. The down- flange edge of each shelf should be on the front side of the stand. The shelves simply rest on the bottom braces (they are not bolted or screwed to the braces). 10. Position the front and rear top supports (items “L”) over the legs. The pre-drilled holes should face the outside of the stand to line up with the threaded-insert holes near the top of the legs. Use the six 5/8" hex-head bolts (items “M”) to secure the top supports to the legs. 11. Attach the angle support brackets (item “N”, shipped with the griddle) to the bottom of the of the griddle using #10x1/2" sheet metal screws (item “O”, also shipped with the griddle). 12. Place the griddle on top of the stand, making sure that the angle brackets that you just installed on the bottom of the griddle are inserted into the front and rear top supports. No additional bolts or screws are required. Lift the griddle only at the ends, never in the middle! 13. Go on to Step 4 on page 18. PAGE 16 OWNER’S MANUAL 1182845 REV 8 HEAVY DUTY COUNTERLINE INSTALLATION Step 3: Attach Restraint for Appliances Mounted on Casters NOTICE For an appliance equipped with casters, (1) the installation shall be made with a connector that complies with the Standard for Connectors for Movable Gas Appliances, ANSI Z21.69 or Connectors for Moveable Gas Appliances, CAN/CGA-6.16, and a quick-disconnect device that complies with the Standard for Quick-Disconnect Devices for Use With Gas Fuel, ANSI Z21.41, or Quick Disconnect Devices for Use with Gas Fuel, CAN1-6.9, (2) adequate means must be provided to limit the movement of the appliance without depending on the connector and the quick-disconnect device or its associated piping to limit the appliance movement and (3) the restraining means should be attached to a frame member on the back of the unit. ! WARNING To avoid accidental gas disconnection and potential explosion: If disconnection of this restraint is necessary to move the appliance for cleaning, etc., reconnect it when the appliance is moved to its originally installed position. Appliances mounted on a stand with casters or other movable surface must be equipped with a restraining means to prevent accidental stress on the flexible gas connection. 1. Secure the restraining-device bracket (item “B” in the followi...

Scarica la tua

Per scaricare, digitare 2 cifre :