valutazioni - , GPA: ( )

Istruzioni per l'uso American Standard, Modello Acrylic 3636.ST

Produttore : American Standard
File Size : 63.59 kb
File Nome :

Lingua di insegnamento:

Il documento viene caricato, si prega di attendere

Scarica la tua primo

Il documento viene caricato, si prega di attendere

Scarica la tua primo

General Cleaning: Do not use abrasive cleaners; a mixture of warm water and a mild liquid detergent is adequate for most cleaning. Strong detergents formulated for use on tile or porcelain-enamel surfaces should be avoided. Caution: Do not allow liquid detergent containers to remain on base surfaces for more than a few moments. Do not use Lestoil, Windex, Mr. Clean, Dow Disinfectant (spray or concentrate), or Lysol Basin, Tub and Tile Cleaner. Do not allow nail polish remover, dry cleaning fluid, acetone, paint remover, or other solvents to contact acrylic surface. Level Level Level base in two directions. 51x102 mm (2x4) Stud Wall Waterproof Drywall 13mm (1/2") minimum Bedding Material Area 3 mm (1/8) 127 mm (5) 51 mm (2) PVC Pipe 159mm (6-5/8) Bedding Material No Bedding Under Apron Before installing drain into the shower base, remove strainer (see Fig. C). This will be installed after shower base is in its final position. Install the drain to the shower base as shown in Fig. D. Use silicone sealant between drain body and shower base. Secure the base to the studs as shown, using the screws and the brackets provided. See Fig. G. Note: Allow the bedding material to completely harden before applying weight to the bottom of the shower base. Draw a line 6-5/8" (159mm) from the sub-floor on to the studs at each side of the opening. Using this line and a level, mark the remaining studs. (See Figs. A & B.) This will be the installed height of the shower base. Mix the low-shrink bedding material (grout, mortar, plaster, etc.). Concrete is not recommended. Apply enough bedding material to support the entire bottom of the shower base. The bedding material must not be used under the apron (front edge). 1 SHOWER BASE 3636.NEO 3838.NEO 4242.NEO 3232.ST 4834.ST 6034.ST 3636.ST 4242.ST 4832.ST 6032.STRH/LH* 5/16" ± 1/16" 3/8" ± 1/16" 5/16" ± 1/16" 3/8" ± 1/16" 1/4" ± 1/16" 1/4" ± 1/16" 1/4" ± 1/16" 5/16" ± 1/16" 1/2" ± 1/16" 1/2" ± 1/16" WASTE PIPE HEIGHT 2 3 4 5 6 A 51 mm (2) PVC Waste Pipe 127mmx127mm (5x5) Opening (See Product Chart for Drain Location) C/L C/L 3636.NEO, 3838.NEO, 4242.NEO 90° 90° 6-5/86-5/8 Insure the floor and stud walls are square and plumb. Provide a 5" x 5" (127mm x 127mm) opening in the floor for the drain (see Figs. A & B). The drain plug accom-modates a 2" (51mm) PVC waste pipe. The waste pipe should extend above the surface of the sub-floor, refer to chart on page 2 for the required dimensions. See product drawings on this page for the specified drain locations. B 3232.ST, 3636.ST, 4242ST, 6034.ST, 4834.ST, 4832.ST 90° 90° 51 mm (2) PVC Waste Pipe 127mmx127mm (5x5) OpeningC/L (See Product Chart for Drain Location) 6-5/8 Tape over the strainer to protect the finish and prevent construction debris from entering the drain. Finish installation as shown in Figure H. After the bedding material has been poured and before it sets, lower the shower base into position with the drain assembly sliding over the waste pipe as shown in Fig. E. It ...