Specification grade,wet listed 71wattMR16lampadjustablefixture. Adjustment mechanism featureshot aiming capability,aiming marks and too- lesslocking. Opticsprovideglare-free50° cutoffto lampandlampimage. Foruse with all halogen MR16lampvari- eties. Unitssmall sizeisidealfortightconstruction areas. Insulation must bekept 3"awayfromsidesand top of fix- ture.Opticalelement can bechanged afterinstallation to providea varietyof distributions. e.g. into a Downlightreflectorin Clear, Gold, Haze, Warm H

Available in 120 or 277V only. 2 Segmented optics not available. 3 Requires 4" round straight pole for CIS. 5" round straight pole for CIG and CIM. 6" round straight pole for CIL. 4 All 70-150W lamps on formed optics and 70-175W lamps on small segmented optics are medium-base, 175-1000W are mogul-base. 5 150W HPS uses S-55 lamp (arc rating of 55V). 6 Must use reduced jacket ED-28 400W lamp when using a segmented optical system in the medium housing. 7 1000W HPS not available in medium housing. M

Transverse mounting with cast-in horizontal aiming protractor and single bolt mounting. BALLAST COMPARTMENT Isolated components for coolest component operation and extended component life. Ballast is rated to start and operate lamp in ambient temperatures down to -20° C. VERTICAL FIXED AIMING Stainless steel mounting arms feature separate vertical aiming pivot bolts and rear re-lamping hinge bolts prevent mis-aiming and provide permanent fixed aiming. Aiming degree markers on both sides of

Reac./HPF2=120V 1D=Type I MCO 7 ACCESSORIES operation and longer ballast life. Each CAS=Arm Solid Top70=70W M=Metal Halide W=CWA 0=208V 2D=Type II MCO optional package seats within the (See Below) CSS=Spider Solid Top 10=100W 3R=SMH C=CWI 4=240V 3D=Type III MCO frame for precise photometric CYS=Yoke Solid Top15=150W K=10KV CWA 57=277V 4D=Type IV MCO repeatability. CAP=Arm Luminous Top 2 17=175W 8=480V 5D=Type V MCO 7 CSP=Spider Luminous Top 2 25=250W W=Multi-Tap wired 120V 2S=Type II Segmented 7

Pole provided with decorative cast aluminum nut covers. 2... Hand hole assembly 4“ x 6“. 3... ASTM 595 steel fluted shaft. Pole cross section is an 8 Sharp Flute. 4 ...Lu minaire arm is 2.375" tubing available in 4', 6', and 8' lengths. Decorative scroll is attached to the underside and to the pole with hex head bolts. 5... Decorative cast aluminum pole cap attached using three (3) set screws. 6... Anchor bolt per ASTM A576 with (2) nuts, (2) flat washer, and (1) lock washer. Nuts, washers

SOCKET Porcelain mogul-base lamp socket with spring-loaded center contact. HOUSING One-piece, die-cast aluminum housing features aesthetically pleasing soft-corner design. ANSI wattage/source label. GASKETING Closed cell gas-filled high temperature silicone gasketing completely seals optical system from dirt, bugs or other foreign material. LENS Thermal shock- and impact- resistant clear tempered glass. OPTICS One-piece hydroformed anodized aluminum reflectors provide five different optical dist

Standard bronze polyester powder coat finish. Other finish colors available. Consult your Streetworks Representative. MOUNTING Clamp type slipfitter for 2 3/8" O.D. pipe. OPTICS Anodized spun aluminum outer reflector housing. Light pattern can be oriented by rotating optical assembly (360°). A degree indicator is provided to identify the aiming position. REFLECTOR Inner hydroformed and anodized reflector. DOOR Die-cast aluminum door with tempered convex glass lens and silicone rubber ga

• Be sure the wall switch is in the ON position. • Be sure that the bulbs are not burned out or broken. Is the surrounding external ambient light too bright? (If so the unit may think it’s daytime.) • Re-aim the head. • Relocate or reposition the unit away from the light. Is the cord plugged onto the sensor head? • Be sure the adapter cord is correctly plugged into the slot on the bottom of the motion sensor mounting plate. TURN OFF POWER BEFORE CONTINUING. Is the wiring to the fixture loose? •