NOTE: Before installing the unit have the following wires installed: 1. A 2 conductor wire with ground (3 wires total) from the power supply panel to the main switch wall box. 2. A 2 conductor wire with ground (3 wires total) from the main switch wall box to the junction box on the unit. NOTE: Use a single pole, single throw (on/off) wall switch that is rated for a minimum of 15 amps. 120 VOLT INSTALLATIONS 1. Locate the voltage selector switch inside the exhaust panel on the top right hand corn

Drill and plug the wall to suit - see Fig. 3. W Fig. 3 Step 2 The hex. stud screw in the slot has to be removed using the allen key provided first, to separate the inner ‘Z’ and outer ‘W’ sleeves of the wall brackets - see Fig. 4. Z Mount the four outer sleeve wall brackets in line with the drilled outW holes using the screws provided - see steps 1 - 4 in Fig. 3. Note: the brackets have slot holes to allow for possible adjustment later. Step 3 X Remove the cap ‘Y’ from the inner sleeve assembly,

MODEL SPECIFICATIONS Model Number Description Voltage Volts Rated Power Watts Remote Control Wall Thermostat Refractory Brick Look AMPS No Heat 120 Volt AMPS 120 Volt AMPS 208 Volt AMPS 240 Volt BF33ST 33” Standard 120/120/208/ 240 245/1440/2100/ 2700 Option Option N/A 2.0 12.0 10.10 11.25 BF33DX 33” Deluxe 120/120/208/ 240 245/1440/2100/ 2700 Option Option Included 2.0 12.0 10.10 11.25 BF39ST 39” Standard 120/120/208/ 240 245/1440/2100/ 2700 Option Option N/A 2.0 12.0 10.10 11.25 BF39DX 39” Del

A charge will be made where a call under the terms of the guarantee has been booked and a failure was not product related, or an engineer arrives and is not able to gain access. If a service call is booked, you or a representative must be present during the Engineers visit. The Dimplex Customer Service Department will be able to inform you whether the fault can be rectified by the provision of a replacement part or an on site visit by a Qualified Service Engineer. In the event of you needing to

Installation If fitted in a room containing a bath or shower, to comply with the current I.E.E. Regulations, a cable outlet will be necessary with the supply to the heater controlled by a double-pole pull-cord switch having a contact separation of 3mm in each pole. The body of the switch should be situated as to be normally inaccessible to a person using a bath or shower. Should Equipotential Earth Bonding be required the earthing conductor in the supply cord is deemed to provide the supplementa

We trust this manual will give you all the answers to the questions that you might have regarding the products. Although every care was taken to ensure the content of this manual is correct we do not accept any liability for claims resulting directly or indirectly from the application of the information contained in this manual. This manual is written specifically for the Dimples Solar product range. Any information contained therein must not be applied generally to any other solar products. Sho

CAUTION - This appliance is not intended for use by chidren or other persons without assistance or supervision if their physical, sensory or mental capabilities prevent them from using it safely. Children should be supervised to ensure that they do not play with the appliance. Precautions should be taken to ensure that prolonged contact with the towel rail cannot occur. Particular care should be taken in confined areas where accidental prolonged contact with the rail could be more likely to occu

Children should be supervised to ensure that they do not play with the appliance. Precautions should be taken to ensure that prolonged contact with the towel rail cannot occur. Particular care should be taken in confined areas where accidental prolonged contact with the rail could be more likely to occur. This appliance should only be used to dry fabrics washed in water using commonly available detergents. IMPORTANT - If the towel rail is to be installed in a place used by the public, a warning