valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
See Cleaning on page 3. 2 309323 Cleaning This is the procedure for flushing the pressure roller. The pump and gun you are using may have additional flushing steps, such as cleaning filters and screens. See the pump and gun flushing instructions. NOTE: Leave the pressure roller attached to the gun for this procedure. See Pressure Relief Procedure on page 2. 1. Relieve the pressure. 2. Remove roller cover (19) and diffuser (23) from roller frame as follows (see Parts Drawing): a. Using your thumb, press down on clip (5) to release end caps (2 &4), diffuser (23) and roller cover (19) into a pail. b. Remove roller cover (19) from diffuser (23). c. Pull end caps (2 & 4) off diffuser (23). 3. Clean roller cover (19), caps (2 & 4) and diffuser (19) with water or a compatible fluid for oil–based materials. 4. Place roller frame (1) in paint pail. Be sure the holes in roller frame (1) are facing inside the paint pail. 5. Prime pump with water or flushing fluid for oil–based materials. Use the lowest pump priming pressure setting. 6. Turn prime/spray valve to SPRAY. NOTE: Perform Step 7 at the lowest pressure possible. 7. Trigger gun until flushing fluid begins to dilute the paint. 8. Place roller frame (1) in another bucket and continue flushing until fluid coming out of the roller frame (1) is clear. 9. Shut off the pump. Turn prime/spray valve to PRIME. Storage If you are going to store the airless equipment for an extended period of time after flushing with water-base fluid, flush again with Graco Pump Armor or mineral spirits/paint thinner. Leave the fluid in the system during storage. Pressure Roller, Model 244279, Series C 1 5 14 12 19 2 4 23 ti10641a 7 17 7* Parts List Ref. No. Part No. 1 2 245999 4 246277 5 197106 7 15H622 12 115524 14 232122 19 107590 23 15B065 25 224399 Description Qty. FRAME, roller 1 CAP, end (includes seal and retainer) 1 CAP, end (includes seal, retainer, and o–ring) 1 CLIP, roller 1 GASKET 2 GASKET 1 EXTENSION, 20 in. (50 cm) 1 ROLLER, cover, 9 inch, 1/2 in. (13 mm) nap 1 DIFFUSER 2 SWIVEL, 45° 1 309323 3 Graco Standard Warranty Graco warrants all equipment manufactured by Graco and bearing its name to be free from defects in material and workmanship on the date of sale to the original purchaser for use. With the exception of any special, extended, or limited warranty published by Graco, Graco will, for a period of twelve months from the date of sale, repair or replace any part of the equipment determined by Graco to be defective. This warranty applies only when the equipment is installed, operated and maintained in accordance with Graco’s written recommendations. This warranty does not cover, and Graco shall not be liable for general wear and tear, or any malfunction, damage or wear caused by faulty installation, misapplication, abrasion, corrosion, inadequate or improper maintenance, negligence, accident, tampering, or substitution of non–Graco component parts. Nor shall Graco be liable for malfunction, damage or wear caused by the incompatibility of Graco equipment with structures, accessories, equipment or materials not supplied by Graco, or the improper design, manufacture, installation, operation or maintenance of structures, accessories, equipment or materials not supplied by Graco. This warranty is conditioned upon the prepaid return of the equipment claimed to be defective to an authorized Graco distributor for verification of the claimed defect. If the claimed defect is verified, Graco will repair or replace free of charge any defective parts. The equipment will be returned to the original purchaser transportation prepaid. If inspection of the equipment does not disclose any defect in material or workmanship, repairs will be made at a reasonable charge, which charges may include the costs of parts, labor, and transportation. THIS WARRANTY IS EXCLUSIVE, AND IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO WARRANTY OF MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE. Graco’s sole obligation and buyer’s sole remedy for any breach of warranty shall be as set forth above. The buyer agrees that no other remedy (including, but not limited to, incidental or consequential damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss) shall be available. Any action for breach of warranty must be brought within two (2) years of the date of sale. Graco makes no warranty, and disclaims all implied warranties of merchantability and fitness for a particular purpose in connection with accessories, equipment, materials or components sold but not manufactured by Graco. These items sold, but not manufactured by Graco (such as electric motors, switches, hose, etc.), are subject to the warranty, if any, of their manufacturer. Graco will provide purchaser with reasonable assistance in making any claim for breach of these warranties. In no event will Graco be liable for indirect, incidental, spe...
Questo manuale è adatto anche per i modelli :Altri strumenti - 309323E (129.01 kb)