Please follow the pre-cautions below for proper care procedures and to prolong the life of your StarBright7. Failure to comply will result in voiding your warranty. Avoid using any chemical compounds or harsh abrasives which will result in permanently damaging the screen material. • USE ONLY a soft non-abrasive cloth with mild soap and water to clean the screen material • DO NOT rub the cloth with force when cleaning to avoid permanently scratching the surface • DO NOT touch the screen surface w

Bracket Hook Black Masking Border Edge Small support rod Locking sleeve White projection surface Lock Bottom Black Masking Big support rod Box Cover Note: Middle foot available on 120” models and above only. Box Foot Base Back Base anchor (available on models 120” and above only) Adjustable up to 1” Adjustment screw for leveling Attention: -Please install the two telescoping support rods simultaneously when pulling up and retracting the screen material. -Do not use the screen in a very strong wi

093009.JA info@elitescreens.com Parts List for WhiteBoardScreen™ Parts List for WhiteBoardScreen™ Please make sure all parts listed are included before proceeding with installation a b c de f G and H are not actual individual parts included but configurations only by combining parts (d) and (e) with the butterfly screw g h Ijk Note: The WhiteBoardScreen™ Series eraser should only be used for the WhiteBoardScreen™. Parts List a. Qty 4 – Butterfly screw b. Qty 12 – Wall screw c. Qty 12 – Hollow wa

For the best results and maximum product longevity, ALWAYS and ONLY use Elite Screens high density whiteboard Eraser. 2. Please use the microfiber cloth and clean water to cleanse the surface every 2-4 weeks to maintain a fresh and clean projection suface. ELITE SCREENS a. c. d. e. b. Insta-DE Screen User’s Guide Adhesive Dry-Erase Front Projection Screen Parts List QTY a. Insta-DE Screen Material 1 b. Pen holder 1 c. Whiteboard pens 3 d. Elite special high density whiteboard eraser 2 e. Microfi

060809-JA info@elitescreens.com Tripod Screen Parts Identification Tripod Screen Parts Identification Top Hook, Keystone Eliminator & Screen Handle Support beam Vertical Extension Bar Screen Material Screen case Carrying handle & Screen height adjustment lock/release tab Tripod junction Tripod Support Legs End cap Vertical locking sleeve ring Using the Screen A. Setting up the screen: Follow the steps below and Fig. 1 & 2. 1. Place the screen in an upright position (fig.1) with the legs toward t

Make sure the brackets are facing the front of the stand. 7. Attach the Holders (j) to the side legs and secure with M6x35 screws (n), M6 washers (q) and M6 nuts (o). (j) holder f (m) M6x20 (i) Bracket d1 d2 b c a (n) M6x35 5 Rev.052411.AS info@elitescreens.com 8. Attach the Projector Rail (g) to the Center Upright Bar (e) and secure with M6x15 screws (l), M6 washers (q) and M6 nuts (o). 9. Attach the Center Upright Bar (e) to the Middle Center Bar (d2) and to the Top Center Bar, and secure with

(2)\a.jpg Hardware Pack F:\..... (2)\c.jpg F:\..... (2)\b.jpg Connecting Bolt X 37 Connector Housing X 37 Shelf Support (nog) X 8 Screw X 8 Controllers IR (Infrared) Remote Control RF (Radio Frequency) Remote Control 3-way Wall Switch (RJ45 Connection) AA Batteries Required Tool C:\Users\Eric\Desktop\....jpg Phillips Head Screwdriver Use of connecting bolts when assembling the components Step1: Use a Phillips Head Screwdriver to attach the Connecting Bolt to the furniture components (unit-A). St

Canvas Bag x 11 2. PicoScreen x 11 How DDo I Set Up The PicoScreeen? 1. Tuurn the bottoom feet to a 990 degree anggle as shown below. Rev.051311.AAS info@@elitescreens.com 2. Hold the base of the PicoScreen with one hand and grip the top handle with the other hand, pull up until the locking mechanism is securely locked into place. How Do I Retract the Pico Screen? 1. Use both hands to retract the PicoScreen. One hand should be under the case and the other on the top to push the retract button. C

062310-JA info@elitescreens.com Kestrel Accessories Kestrel Accessories Qty 1 Radio Frequency Remote Control Qty 1 Infrared Remote Control Qty 2 AAA batteries Qty 1 Qty 1 Qty 1 5-12V Trigger Low Voltage 3-way IR “eye” Receiver Wall Switch IMPORTANT SAFETY NOTES 1. Please read this manual before use and follow the procedures specified: a. Please retain this manual for future reference. b. To avoid any damages to the screen, do not use any accessories or parts not recommended by Elite Screens. c.

Please follow the instructions in this package. With proper care, your QuickStand screen will provide many years of reliable service. Two Section Frame (For presentation screens that are less than 120” in diagonal measurement) 1. Take the frame out of the case and remove its wrappings. Unfold the main joints as shown in (fig 1). 2. Once the main joints are unfolded, make sure that the snap latches “click” into the locked position. The frame should now be fully elongated as in (fig2). *Note: The