valutazioni - 1, GPA: 4 ( )

Produttore : Samsung File Size : 21.27 mb File Nome : Lingua di insegnamento:

Install the batteries (type AAA) before use. Lift the battery compartment cover at the back of the remote control, while pressing the locking tab. Install the batteries into the remote control as shown by the figure below. (If the batteries are installed with the wrong polarity, the remote control will not work.' After inserting the tip of the cover into the slot, push the other end to close it until it clicks into place. * Specification: AAA type batteries 18_ assembling the cleaner 1. Battery Level Indicator - Charging: Shows the charging progress in 3 steps. - In Use: Shows the battery charge level. The battery charge level is reduced by each level from FULL while operating. 2. Recharging - This icon turns on when the Vacuum cleaning Robot returns to the charger station to charge its battery. 3. Cleaning Mode Display - Each time the cleaning mode button is pressed, the corresponding cleaning mode is displayed. (A) Auto Mode: This icon turns on when Auto cleaning mode is selected. (B) Spot Mode: This icon turns on when Spot cleaning mode is selected. (C) Max Mode: This icon turns on when Max cleaning mode is selected. 4. Check Code - The Check Code icon will turn on if an issue arises that needs your attention BUTTON PART 5. Cleaning Mode - Press to select a cleaning mode. After selecting a cleaning mode, press the ( ® ) button to start cleaning. 6. Start/Stop - Press to start/stop cleaning. 7. Recharging - When this button is pressed, The cleaning robot will return to the charger station to charge its battery. assembling the cleaner _19 02 ASSEMBLING THE CLEANER operating tne cleaner INSTALLING THE VACUUM CLEANING ROBOT Installation order 1. Turning the Power Switch on or off To use the vacuum cleaning robot, you must turn on the Power Switch at the bottom of the main unit. 2. Installing the Charger To charge the vacuum cleaning robot, you must first install the charger. Since the battery is discharged when the product is purchased, you must fully charge the battery before use. 3. Charging the Battery You should charge the battery completely before using the vacuum cleaning robot. Turning the Power Switch on or off To use the vacuum cleaning robot, you must turn the Power Switch on. If you turn the Power switch off, all settings will be reset. 1. Turn over the main unit and turn the Power Switch on. - If the icons are not turned on, it indicates that the battery charge is depleted. In this case, dock the Vacuum cleaning Robot to the charger station after turning the Power Switch on. - Note that turning the Power Switch off will reset all settings. - When no key is pressed for approximately 10 minutes when the power is on, the power is automatically turned off to save battery power. In this case, to use this Vacuum cleaning Robot again, please push the “Power” button or ® button. A If the Power Switch is turned off, the Vacuum cleaning Robot will not be charged even if it is CAUTION docked with the charger station. 20_ operating the cleaner Installing the charger 2. There should be no obstacles and cliffs 0.5m to the left and ^ right and within 1 m of the front. 3. Install the charger in a location where it can be easily accessed by the vacuum cleaning robot. \]§> 4. Arrange the power cord along the wall. 5. When the floor is made of wood, install the charger in the same direction as the grain of the wood. ete> Always keep the power cord of the charger plugged note into the power outlet. \ - If no power is supplied to the charger, the vacuum cleaning robot will not be able to find the charger and will not be able to charge automatically. - If the vacuum cleaning robot is separated from the charger, the battery is automatically discharged. ;<*r _ operating the cleaner _21 03 OPERATING THE CLEANER operating tne cleaner Charging When the product is initially purchased, the battery is fully discharged, and you must charge the vacuum cleaning robot manually. Turn on the Power Switch at the bottom of the product. 1. After aligning the charge pins of the main unit with the charge pin of the charger station, press the main unit Power lamp until you hear a Recharging power sound from the charger. - The Charging Lamp turns green. Charging lamp 2. Check the charge status of the vacuum cleaning robot. - When it is fully charged, all three bars of the battery level icon will Flash simultaneously. ■ If the following appears in the display (as seen in the figure below) 10 seconds after connecting the robot cleaner to the charging station, it indicates that the power switch is turned off. In this case, please turn on the power switch at the bottom of the cleaner. <□- CD- -ŒD ■a ■ When the battery level display flashes while cleaning, the Vacuum cleaning Robot stops vacuuming and automatically charges itself at the charger. ■ If the battery level icon on the display moves to the right as shown while the cleaner is operating, the cleaner can no longer ...

Scarica la tua

Per scaricare, digitare 2 cifre :