valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
reset radio / aux. snooze / dimmer Back Panel Sleep Button AUX. in Jack DST Switch DC Jack FM Antenna EXB Button Time Sync/Set Button Thank you for purchasing the iP40. Designed specifically to work with your iPhone and iPod, this system provides high quality audio performance that brings out the best in your music and lets you wake or sleep to it. Please read this instruction carefully before the appliance is operated and keep it for future reference. Install iPhone/iPod Insert Your iP40 comes with a set of inserts to ensure your iPhone or iPod fits properly in the dock on the top of the system. To place an insert: 1. Select the insert for your iPhone/iPod. 2. Gently press the iPhone/iPod insert into the dock. 3. Carefully place your iPhone/iPod into the dock. The iPhone/iPod must not be in a case or “skin”. 4. To remove/replace an insert, first remove your iPhone/iPod, grip the insert and pull gently upwards. Getting Started Install Insert 3 iP40 Display Time Display PM Indicator iPhone/iPod Indicator Aux Indicator Radio Indicator Buzzer Indicator Alarm Indicator Sleep Indicator EXB Indicator Wake-to Indicator Battery Low Indicator 1. Depending on your location and whether or not DST (Day Saving Time) is in effect, set the DST Switch located at the back of the unit to +1 to add an hour or to -1 to subtract an hour. Time Sync from iPhone/iPod The iP40 Time Sync feature allows you to sync the time on the iP40 to the time on your iPhone or recent model iPod (iPod Touch, iPod Nano and iPod Classic; older iPod models such as iPod mini do not support this feature). 1. Press the Time Sync/Set Button located at the back of the unit. A cursor will flash on the the display, indicating the unit is attempting to sync. 2. Once sync is completed two beeps will confirm sync was successful and the new time will be displayed. 3. If sync was not successful, one long beep will sound. If this happens, please try again with a different iPhone/iPod. Note: iPhone time is automatically updated to the correct time via cell phone towers. The time on your iPod is accurate only to the time on the computer the last time the iPod was synced to it. It’s possible to have up to 59 seconds difference between the iP40 and synced iPhone or iPod. Setting Up the iP40 4 Installing/Replacing the Clock Backup Battery The iP40 requires a CR2032 lithium battery (included) to provide backup power to the clock in the event of a temporary power interruption. The CR2032 backup battery was packed in the same poly bag with this instruction manual. 1. Place the clock radio face down on a flat surface. 2. Slide the battery door in the direction of the arrow and then lift the door by the opposite edge to remove it from the radio. 3. Install the CR2032 backup battery in the battery compartment with the “+” side facing up as shown in the illustration. 4. Replace the battery door. If AC power is interrupted the backlighting in the display will go off and the radio or docked iPod/iPhone will not play. However, the buzzer alarm will still turn on at the selected time to wake you up, even if you had selected the Wake to Radio, or Wake to iPod alarm modes. When the Battery Low Icon appears in the display it is time to replace the battery. Purchase a fresh CR2032 battery, available wherever batteries are sold. Follow steps 1 through 4 above to remove the exhausted battery and install the fresh battery. IMPORTANT: To avoid having to reset the time and wake up time, leave the radio connected to the AC outlet when you install the new backup battery. Note: Make sure you dispose of the exhausted lithium battery properly, according to your local regulations. Installing Backup Battery Setting Up the iP40 5 Setting Time 1. Press and hold the Time Sync/Set Button located at the back of the unit for 2 seconds until the time display flashes. Press the << or >> button to set the current hour (hold to advance rapidly). 2. Remember to set the correct AM or PM. The PM Indicator is located on the upper left hand side of the time display; there is no AM indicator. 3. Press the Time Sync/Set Button again to adjust minutes. Press the << or >> button to correct time. 4. If desired, press the Button during time setting to toggle the clock format between 12 hour and 24 hour display mode. 5. Press the Time Sync/Set Button again (or no button within 10 seconds) to exit the time setting mode. Using the Alarm Setting the Alarm 1. Press and hold the Button until the alarm icon and alarm time flashes. Press the << or >> Button to set the alarm hour. Remember to set the correct AM or PM time. 2. Press the Button again to adjust minutes. Press the << or >> Button to set the alarm minutes. 3. Press the Button again to select wake to sound source. Press the << or >> Button to select wake to iPhone/iPod, radio or buzzer. Note: if selected wake to source is iPhone/iPod but no iPhone/iPod is docked/detected, the iP40 will automatically switch to wake to buzzer. 4. Press the button again or if no k...
Questo manuale è adatto anche per i modelli :ricevitori radio - iP40 (406.73 kb)