Cleaning Pump Turn Pressure to HIGH (completely clockwise) 3 4 Lift Suction Assembly above Paint Level in Bucket Turn Prime/Spray Control to PRIME Position 1 6 Wipe Exterior of Suction Assembly and Bypass Tube Suction Assembly and Bypass Tube in Bucket of cleaning fluid 2 Turn power switch to ON (shown in the OFF position) 5 Airless Paint Sprayers Operating Instructions and Assembly Instructions Cleaning Hose and Gun Turn Prime/ Spray Control to SPRAY (knob is vertical) If Reversible Tip is Used

Suction filter Before each use Every 25 gal. or Yes and every 5 gal. more often if required Gun filter Before each use Every 25 gal. Yes Do not attempt to clean gun filter, only replace. Roller nap Before each use As required Yes Prime/spray valve Before each use Every 1000 gal. Yes 3/4” Wrench, torque to 80 in/lbs. Push button Before each use Every 1000 gal. Yes 7/8” Socket or wrench, torque to 200 in/lbs. Block bolts Before each use Do not require Yes Block bolts are to be torqued to 275 in/lb

Always ground the pump and spraying surface. Always use a 3-wire grounded extension cord and power receptacle. . Do not use paints or solvents containing halogenated hydrocarbons such as methyl bromine, carbon tetrachloride, and ethyl iodine. Keep hose away from sharp objects. Bursting hoses may cause injury. Examine hoses regularly and replace if damaged. . Check hoses for weak or worn condition before each use, making certain that all connections are secure. . Keep area clean and free of paint

NOTE: Strain and thin paint before using. All paint may have particles that will clog filter and spray tips. Remove any skin which may have developed on Operating Instructions and Assembly Instructions Airless Paint Sprayers the paint due to air exposure. Follow paint manufacturers’ recommendations on thinning paint. 12. When pure paint appears from spray tip rotate tip to the Spray position. The system is now ready for use. Clean Position 1 Spray Position 2 12” Holding Spray Gun Thin Coat Thin

APPrOPrIATE ExTENSION COrD GAUGE FOr GIvEN lENGThS length of Cord Gauge 25’ 14 25-50’ 12 50-100’ 10 Operating Instructions and Assembly Instructions Airless Paint Sprayers Skin Injection Ha zard: . High pressure spray can inject toxins into blood stream. If injection occurs, seek emergency medical treatment. Use a face mask/respirator and protective clothing when spraying. Always spray in a well ventilated area to prevent health and fire hazards. Refer to Material Safety Data Sheets (MSDS) of sp

Part No. Description No. Q ty. R ef. Part No. Description No. Q ty. 10 Suction Bell (with filter) AL111000AJ 1 11a Suction Tube Assembly AL138400SV 1 11b Option, Solvent Resistant AL138404SV 1 12 Bucket Support (with screws) AL168080SV 1 13 Wheel, Pneumatic (optional) WA005620AV 2 14 Cap, Rubber (optional) MJ110300AV 2 15 Bucket Support (w/screws & nuts) AL167953SV 1 16 Stand AL168020AD 1 15 16 14 13 12 11 10 9 8 7 6 5 4 3 2 1 8 1 2 3 4 5 6 Operating Instructions and Assembly Instructions Troubl

2 ApplicationChart................................. 2 SafetyGuidelines................................. 3 GeneralSafetyInformation ........................ 3 AssemblyInstructions ............................. 6 Preparation...................................... 6 SprayingInstructions.............................. 8 Cleanup........................................ 10 Storage........................................ 14 SprayGunMaintenance.......................... 15 MaintenanceChart.................

Before performing any maintenance, make sure to relieve pressure from system and disconnect power from sprayer. • Do not use oil based solvents to clean equipment after using latex based coatings. Use only warm soapy water. • Always replace clogged gun filters, do not attempt to clean them. • Carefully follow cleaning and storage instructions for your sprayer. • Do not use metal or other hard objects to pick dried paint material from Spray Tip Orifice. TrIGGEr lOCk pulling the trigger must not o

hOw TO ChANGE SPrAy TIPS It may be necessary to change spray tips during a paint job. Follow these steps for safe, easy tip changes. 1. Depressurize and turn off unit per manufacturer’s instructions. 2. Engage gun trigger lock. 3. Pull red tip insert out of spray base and replace with different tip, fully inserting tip into base. hOw TO ATTACh rOllEr ACCESSOry 1. Depressurize and turn off unit per manufacturer’s instructions. 2. Engage gun trigger lock. 3. Remove spray base, tip, seal and washer

5 6 Operating Instructions and Assembly Instructions Airless Paint Sprayers Preparation Airless painting systems, unlike most other power tools, require additional care to ensure proper working order. Following these instructions will significantly increase the likelihood of having a positive paint experience. It is important that the painting equipment is flush/tested EACH time a new job is started. Each pump is tested at the factory with a fluid that must be flushed from the system prior to pa