valutazioni - 4, GPA: 4.3 ( )

Produttore : Kenwood File Size : 1.26 mb File Nome : Lingua di insegnamento:

2. Be sure to remove the power cord from the AC outlet before plugging or unplugging any connection cords. Plugging/unplugging connection cords without disconnecting the power cord can cause malfunctions and may damage the unit. 3. Do not connect power cords from components whose power consumption is larger than what is indicated on the AC outlet at the rear of this unit. Analog connections Audio connections are made using RCA pin cords. These cables transfer stereo audio signal in an “analog” form. This means the audio signal corresponds to the actual audio of two channels. These cables usually have 2 plugs at each end, red for the right channel and white for the left channel. These cables are usually packed together with the source unit, or are available at your local electronics retailer. Microcomputer malfunction If operation is not possible or an erroneous display appears, even though all connections have been made properly, reset the microcomputer by referring to “In case of difficulty”. . INPUT MODE 1 Use the INPUT SELECTOR knob to select CD/DVD, VIDEO2, DVD or DVD/6CH (VR-715/KRF-V5070D only). 2 Press the INPUT MODE key. Each press switches the setting as follows: In DTS play mode 1 F-AUTO (digital input, analog input) 2 D-MANUAL (digital input) In CD/DVD, VIDEO2, DVD or DVD/6CH (VR-715/KRF-V5070D only) play mode 1 F-AUTO (digital input, analog input) 2 D-MANUAL (digital input) 3 6CH INPT (DVD/6CH input) 4 ANALOG (analog input) Digital input: Select this setting to play digital signals from a DVD, CD, or LD player. Analog input: Select this setting to play analog signals from a cassette deck, VCR, or record player. Auto detect: In “F-AUTO” (full auto) mode (AUTO DETECT and DIGITAL indicators light up), the receiver detects the digital or analog input signals automatically. Priority is given to digital signal during input mode selection. The receiver will select the input mode and listening mode automatically during playback to match the type of input signal (Dolby Digital, PCM, DTS ) and the speaker setting. The initial factory setting is full auto. To keep the receiver set to the currently selected listening mode, use the INPUT MODE key to select “D-MANUAL” (digital manual). However, even when this setting is selected, there may be cases in which the listening mode is selected automatically to match a Dolby Digital source signal depending on the combination of listening mode and source digital. In D-MANUAL mode, if the audio reproduction stops in the middle due to change in the input signals, etc, press the LISTEN MODE key. If the INPUT MODE key is pressed quickly, sound may not be produced. Press the INPUT MODE key again. 8 EN Setting up the system Setting up the system Connecting audio components SYSTEM CONTROL jacks % + - + - Australia Other countries U.S.A. and Canada To AC wall outlet AUX REC OUT PLAY IN VIDEO1 PLAY IN R AUDIO IN OUTIN OUT OUT Cassette deck or MD recorder CD or DVD player Video component ) Other component OUT 9 EN Setting up the system Setting up the system + - + - REC OUT VIDEO 2 IN DVD IN MONITOR OUT VIDEO 1 OUT VIDEO 1 IN PLAY IN VIDEO 1 VIDEO AUDIO For VR-705/ KRF-V4070D/ V5570D only Video Audio IN/OUT IN/OUT Video inputs and outputs (Yellow RCA pin cords) Audio inputs and outputs OUT OUT Monitor TV Video inputs (Yellow RCA pin cords) VIDEO IN Video deck IN IN OUT OUT OUT OUTDVD player or LD player DVD player or LD player A video component with digital audio outputs should be connected to the VIDEO 2 jacks. 10EN Setting up the system Setting up the system The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals. If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully. + - + - VIDEO 2 DVD CD / DVD COAXIAL OPTICAL DIGITAL IN Component with DTS, Dolby Digital, or PCM COAXIAL DIGITAL OUTCOAXIAL DIGITAL OUT (AUDIO) DOLBY DIGITAL RF OUT (AUDIO) PCM OUT RF digital demodulator (DEM-9991D) (sold separately) CD or DVD player OPTICAL DIGITAL OUT (AUDIO) Optical fiber cable COAXIAL DIGITAL OUT (AUDIO) Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.) 0 LD player To connect an LD player with a DIGITAL RF OUT, connect the LD player to the KENWOOD RF digital demodulator (DEM-9991D). Next, connect the DIGITAL OUT jacks of the demodulator to the DIGITAL IN jacks of the receiver. Connect the video signal and analog audio signals to the VIDEO 2 jacks. (See “Connecting video components”.) 11EN Setting up the system Setting up the system If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully. 8 + - + - CENTER SUB WOOFERSURROUNDFRONT VIDEO 1 OUT VIDEO 1 IN VIDEO 2 IN DVD IN MONITOR OUT VIDEO 2 DVD/6CH CD / DVD COAXIAL OPTICALDVD / 6CH INPUT VIDEO DIGITAL IN SURROUND OUT L/R VIDE...

Scarica la tua

Per scaricare, digitare 2 cifre :