Make sure SEAL WASHER (3) and FRICTION WASHER (4) are installed. Do not tighten fully. 3. Insert the DOWN TUBE (5) into the SPUD COUPLING NUT (2) and push it down. Note: If cutting Down Tube (5) to size, note that Critical Line (C/L) on Vacuum Breaker must typically be 6" (152mm) above fixture. Consult Code for details. Fig.3 CENTER LINE OF FIXTURE SPUD FINISHED WALL FILE EDGES SOLDER ADAPTER ADAPTER 32mm (1-1/4) A (A-B)= BC CLEAN Fig. 4 Fig. 4a Fig. 4b Fig. 4c 1 1 4 2 3 TEFLON TAPE FINISHED WAL

rear cover To check the product suitability for commercial and multiple installations, please contact Triton's specification advisory service before installation. Telephone: 0870 067 3767 Facsimile: 0870 067 3334 E mail: technical@tritonshowers.co.uk Combi HP thermostatic mixer shower INTRODUCTION This book contains all the necessary fitting and operating instructions for your Triton high pressure thermostatic mixer shower. Please read them carefully. Please read through the whole of thi

out notice. Specification sheet revised 4/2008 Product Features • Solid brass holder • Glass cup • Brush with durable nylon bristles Available Finishes Chrome Brushed Nickel 40522XX0 40522000 40522820

When satisfied with the action of the drain, slide the other end of the spring clip over the end of the horizontal rod. plunger height adjuster flange sealing gasket link mack gasket spring clip friction ring retainer nut nut horizontal rod pivot ball pivot ball seals pivot tee tailpiece Robinets de lavabo Limbo C Tango C Swing C Solaris E Stratos E Metro E A prendre en consideration pour l’installation Pour de meilleurs resultats, Hansgrohe recommande que ce produit soit installe par un plombie

Due to air in the faucet, the spray pattern may be unattractive for the first 10 - 15 uses after installation or service. 32110XX1/32112XX1 only: pull the temperature lever forward to make the water cooler, backward to make it warmer. 3 4 1 2 Temperature adjustment - 32111XX1 / 32113XX1 only Turn the water supplies off (1). Disconnect the faucet power cable from the battery pack or AC power pack (2). Remove the screw from the rear of the faucet (3). 3 2 1 Remove the faucet body (1). Turn the tem

20 The measurements shown are for reference only. Products and specifications shown are subject to change without notice. Specification sheet revised 1/2009

Congratulations on purchasing your American Standard faucet with Speed Connect drain, a feature found only on American Standard faucets. *Your new American Standard faucet is designed to work only with the Speed Connect drain. Speed Connect Drain* • Fewer parts, installs in less time • Never needs adjustment • Guaranteed to seal properly the first time, every time. COLLAR ON MOUNTING NUT 8 2 4 3 1 8 1 INSTALL FAUCET 7420.101 & 7415.101 Turn off hot and cold water CAUTION supplies before beginnin

30000 4 sprayhead douchette poing Ducha extraible completo 14893XX1 5 mounting kit fixation cpl Set de fijación completo 95049000 6 connection hose flex Connexión flexible 95048000 7 squeezing connection raccord à bague sertie Tuercas gifería 96099000 8 hose weight contrepoids contrapeso 98551000 9 check valve clapet anti-retour Válvula antirretorno 94074000 10 screw cover cache vis Tapón 96338000 11 baseplate escutcheon Florón 06329XX0 12 mounting kit fixation cpl Set de fijac

5,819,789 HOT COLD Turn off hot and cold water CAUTION supplies before beginning. Installation Instructions 2064.451 ROUGHING-IN DIMENSIONS 1 2" D. (52mm) 1" (25mm) 2" MIN. (51mm) 3" MAX. (76mm) MAX. FINISHED WALL FINISHED WALL 2" D. (52mm) 9-1/4" (235mm) 1/2" NPT INLETS 8" (203mm) 4" CROSS (102mm) HANDLE 1 INSTALL VALVE BODY Determine where the finished wall location will be. This measurement is very important! Note: The rough-in measurement from the finished wall is; 2" minimum and 3" maximum.