valutazioni - 3, GPA: 4.3 ( )

Produttore : Analog Devices File Size : 1.45 mb File Nome : Lingua di insegnamento:

Cr, Cb: 0.7 Vp/p. Impedance: 75 Ohm. • S.VIDEO Connector: 4-pin mini DIN female. Standard: PAL : 15.625 kHz / 50 Hz - 625 lines. NTSC : 15.734 kHz / 59.94 Hz - 525 lines - 7.5 IRE. Level: Y : 1 Vp/p (0.7 V Luma + 0.3 V Sync.). C : 0.7 Vp/p (0.3 V Chroma Burst). Impedance: 75 Ohm. • COMPOSITE VIDEO Connector: BNC female. Standard: PAL : 15.625 kHz / 50 Hz - 625 lines. NTSC : 15.734 kHz / 59.94 Hz - 525 lines - 7.5 IRE. Level: 1 Vp/p (0.7 V Luma + 0.3 V Sync.). Impedance: 75 Ohm. • FRAME LOCK Connector: BNC female. Rate: Same rate as the output frame rate. Signal: TTL level. • SDI* Connector: BNC female (x2). Signal: 270 Mbps (4:2:2 – 10 bits) serial digital output. Impedance: 75 Ohm. • HD-SDI (MODELS: BHD930-AG & BHD930-DG only) Connector: BNC female. Signal: 1.5 Gbps (4:2:2 – 10 bits) serial digital output. Format: 720p @ 60, 59.94 & 50 Hz (SMPTE 296M) 1080i @ 60, 59.94 & 50 Hz (SMPTE 274M) 1035i @ 60 & 59.94 Hz (SMPTE 260M) 1080sF @ 30, 29.97 & 25 Hz (RP2H/SMPTE 274M) 1080p @ 30, 29.97, 25, 24 & 23.98 Hz (RP2H/SMPTE 274M) Impedance: 75 Ohm. • ANALOG (SD/HD) LUMA KEY (HD available on BHD930 models only) Connector: BNC female. Format: Same format as the output. Level: 0.7 Vp/p. Impedance: 75 Ohm. * Available on the BSD830 & BHD930 models only. PAGE 35 Chapter 7 : TECHNICAL SPECIFICATIONS (continued) BROAD SCAN (HD/SDI) 7-2. VIDEO OUTPUTS (continued) • SDI LUMA KEY* Connector: BNC female (x2). Format: Same format as the output. Impedance: 75 Ohm. • HD-SDI LUMA KEY (available on BHD930 models only) Connector: BNC female (x2). Format: Same format as the output. Impedance: 75 Ohm. * Available on the BSD830 & BHD930 models only. 7-3. ANALOG GENLOCK (MODELS: BHD930-AG, BSD830-AG & BSC730) Connectors: 2 BNC female. Input signal type: Black Burst (PAL or NTSC) or 3-level HD black. Impedance: 75 Ohm. Output: Active loop-through. 7-4. DIGITAL GENLOCK (MODELS: BHD930-DG & BSD830-DG) Connectors: 2 BNC female. Input signal type: SD/HD-SDI Black. Impedance: 75 Ohm. Output: Active loop-through. 7-5. COMMUNICATION PORTS • RS-232 Connector: DB9 female. Data Rate: 9600 Bauds, 8 data bits, 1 stop bit, no parity bit, and no flow control. Pin-out: PIN # FUNCTIONS 2 Tx (transmit data to the control device) 3 Rx (receive data from the control device) 5 GROUND (Gnd) 8 Reserved for manufacturer. DB9 connector • LAN (Optional) Connector: RJ-45 female. Protocol: TCP (Transmission Control Protocol) UDP (User Datagram Protocol). Data Rate: 10 / 100 Mbps. LED functions (on RJ45 connector): Left LED Right LED Meaning OFF OFF No link OFF ON 100 BASE-T link. ON OFF 10 BASE-T link. PAGE 36 BROAD SCAN (HD/SDI) Chapter 7 : TECHNICAL SPECIFICATIONS 7-6. ENVIRONMENTAL Power Supply: 100VAC-250VAC ; 50-60Hz ; I = 0.5A Max. Storage Temperature: - 25 °C to + 85 °C (-13 °F to + 185 °F) Operating temperature: 0 °C to + 50 °C (32 °F to 122 °F) Hygrometry: 10% to 80% (without condensation) Dimensions: Compatible with the 19" standard, height = 1 unit. W 482 mm (19”) x D 265 mm (10.4”) x H 44 mm (1.74”). Weight: 3.3 kg (7.3 Lbs.). PAGE 37 BROAD SCAN (HD/SDI) APPENDIX A: PROGRAMMER'S GUIDE A-1: INTRODUCTION If you need to use your own Software Control program from a PC or WORKSTATION with an RS-232 port, the device allows communication through an ASCII code protocol. The device treats any character that it receives on the RS-232 as a possible command but only accepts legal commands. There is no starting/ending code needed in a command string. A command can be a single character typed on a keyboard and does not require any special character before or after it. (It is not necessary to press "ENTER" on the keyboard). A command can be preceded by a value (See chapter A-2: COMMANDS STRUCTURE). When the device receives a valid command, it will execute the command. Then it will send back the status of the parameters that have changed due to this command. If the command cannot be executed (value out of range, no signal on the selected input), the device will just sends back the current status of the corresponding parameters. If the command is invalid, an error response will be returned to the control device. All responses returned to the control device end with a carriage return and a line feed signaling the end of the response character string (see chapter A-3: ERROR RESPONSE). A-2: COMMANDS STRUCTURE Commands are usually composed of a numerical value followed by the command character. The characters used without any numerical value return the current setting of the command. Command = Value (optional) + Character. Examples / Exemples: ANNEXE A: GUIDE DE PROGRAMMATION A-1: INTRODUCTION Si vous souhaitez utiliser votre propre logiciel de controle avec votre PC, MAC ou Station de Travail par un port RS-232, l'appareil peut communiquer par simple emission / reception de caracteres ASCII. L'appareil traite tous les caracteres recus sur son port RS-232 comme des commandes possibles; seules certaines commandes sont reconnues et acceptees. Une commande est con...

Scarica la tua

Per scaricare, digitare 2 cifre :