valutazioni - 4, GPA: 3.8 ( )

Produttore : Analog Devices File Size : 1.45 mb File Nome : Lingua di insegnamento:

..[23.97 Hz] ..[24 Hz] ..[25 Hz] ..[29.97 Hz] ..[30 Hz] ..[50 Hz] ..[59.94 Hz] ..[60 Hz] ..[Frame lock]: The output frame rate is synchronized onto the frame rate of the signal connected to the genlock input. PAGE 22 BROAD SCAN (HD/SDI) Chapter 4 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued) 4-5. FUNCTIONS DESCRIPTION (continued) ..[Genlock Tune]. This function is available only if the Output format selected is Genlock, and if a correct genlock signal is detected on the GENLOCK INPUT connector. ..[H Phase]: This function allows adjusting the genlock horizontal phase. Adjust with ....+ ENTER. ..[SC. Phase]: This function allows adjusting the genlock Subcarrier phase. (Available with Analog SDTV Genlock signal only). Adjust with ....+ ENTER. ..[Type] Available for SDTV output format. Select the needed signal available on the RGB/YUV output ..[RGBS]: RGB/S video output. ..[RGsB]: RGB with Sync on Green video output. ..[YUV]: Component video output. ..[Pedestal] Available for NTSC output format. Add a pedestal to the NTSC output format. ..[Test pattern] Select one item with ....+ ENTER. ..[Grey Scale]: Displays onto the output a grey scale pattern. ..[Color bar]: Displays onto the output a color bar pattern. ..[Grid]: Displays onto the output a grid pattern. ..[SMPTE]: Displays onto the output a SMPTE pattern ..[No]: turns OFF the test pattern. ..[IMAGE] ..[Auto Centering] This function centers automatically the image source in the screen and then for the RGB signal, performs pixel clock & phase adjustments. ..[Optimize] ..[Clock]: Manual adjustment of the pixel clock. ..[Phase]: Manual adjustment of the pixel phase. ..[Aspect in] Select the Aspect Ratio of your input source with ....+ ENTER. ..[4/3 standard]: 4/3 input format. ..[16/9]: 16/9 input format (computer). ..[Aspect out] Select one of the following output aspect ratio with ....+ ENTER. ..[Standard]: The entire image and the aspect ratio are preserved. ..[Crop]: The image is zoomed without deformation to fill the screen, but some borders of the image will be cropped. The aspect ratio is preserved. ..[Full Screen]: The image is stretched to fill the screen. The aspect ratio is not preserved. ..[Zoom]: The image can be zoomed, cropped and stretched at your convenience. ..[Under/over] Select an item with ....+ ENTER. ..[Underscan]: The output image is full screen. ..[Overscan]: The output is 10% bigger than in underscan mode. ..[RGB Levels] (Available for analog input source only). Select an item with ....+ ENTER. ..[Red]: Adjust the level of the Red with ....+ ENTER. ..[Green]: Adjust the level of the Green with ....+ ENTER. ..[Blue]: Adjust the level of the Blue with ....+ ENTER. ..[Black Level] Adjust the Black level with ....+ ENTER. PAGE 23 Chapter 4 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued) BROAD SCAN (HD/SDI) 4-5. FUNCTIONS DESCRIPTION (continued) ..[Gamma] Select one of the 8 levels of the anti-flicker with .... and validate with ENTER. ..[Flicker filter] Select one of the 8 levels of the anti-flicker with .... and validate with ENTER. ..[Sharpness] Adjust the image sharpness with .... and validate with ENTER. ..[Preset] This function allows to set all the image parameters (flicker filter, Black level, RGB level, under/overscan, position & size) to the factory settings. FUNCTION POSITION FUNCTION POSITION R, G, B levels 0 Flicker filter 4 Black level 0 Sharpness 0 Gamma 1 ..[AUDIO] Available on BHD930 & BSD830 models. ..[Embed. ON/OFF] Allows embedding analog audio stereo signal into the HD/SD-SDI signals. ..[Mute ON/OFF] Switch ON or OFF the audio output. Validate with ENTER. ..[Level] Adjust the audio level with ....+ ENTER. ..[Balance] Adjust the balanced level with ....+ ENTER. ..[LUMAKEY OUT] ..[Lumakey ON/OFF] Allows activating Luma key outputs. ..[Threshold] ..[Offset up] Offset up adjustment. ..[Offset down] Offset down adjustment. ..[Gain] Gain level adjustment. PAGE 24 BROAD SCAN (HD/SDI) Chapter 4 : FRONT PANEL DISPLAY MENU DESCRIPTION (continued) 4-5. FUNCTIONS DESCRIPTION (continued) ..[LOGOS/FRAME] Available on BHD930 & BSD830 models. ..[Frame ON/OFF]. Display ON or OFF the stored frame onto the output. ..[Logo] ..[Logo OFF]: Display off the logo. ..[Logo 1]: Display the logo 1. ..[Logo 2]: Display the logo 2. ..[Logo 3]: Display the logo 3. ..[Logo 4]: Display the logo 4. ..[Logo Animated]: Display the animated logo. ..[Record frame] This mode allows storing up a frame in order to display them at any time during the show. ..[Size] Adjust the size of the frame area with ....+ ENTER. ..[Position] Adjust the position of the frame area with ....+ ENTER. ..[Store] This function allows storing the displayed image (frame). Presses ENTER to start the memorization of the frame. The memorization will take about 2 minutes. ..[Record logo] This mode allows storing up to 4 logos in order to incrust them into the displayed image. Select an item with ..• + ENTER. ..[Size] Adjust the size of the logo area with ....+ ENTER. ..[Positio...

Scarica la tua

Per scaricare, digitare 2 cifre :