< :> indicates the ‘or’ condition. For which user has a choice for the options listed within, and only one can be specified. <~> indicates the value range. For which user has a choice for the values within the range, and only one can be specified. <,> indicates a separation between integer values. ACCUSYS, INC. 5F, 38 TAIYUAN ST, JHUBEI, HSINCHU, TAIWAN, R.O.C. TITLE EXPERAID COMMAND LINE INTERFACE USER GUIDE PROJECT “DESKTOP RAID” DOCUMENT STATUS OFFICIAL RELEASE REV. G–05-NOV-2007 PAGE 11 OF 2

The on-board floppy controller is shipped with a jumper installed at J6, position 6, floppy enabled. If the floppy controller on the AHA-1742A is not used, this jumper should be removed. Only one floppy controller per EISA system can be enabled. The AHA-1740A/1742A/1744 has a jumper that can be changed. This is the jumper block labeled J4, near the external connector. This determines whether or not the AHA-1740A/1742A/1744 will provide termination power to the SCSI bus. By default, the jumper is

All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means; electronic, mechanical, photocopying, recording or otherwise, without the prior written consent of Adaptec, Inc., 691 South Milpitas Blvd., Milpitas, CA 95035. Trademarks AMI is a registered trademark of American Megatrends, Inc. ASPI is a trademark of Adaptec, Inc. IBM PC-AT and OS/2 are registered trademarks of International Business Machines Corporation

• Make sure that the SCSI boot drive address is set to SCSI ID 0:0. Check the drive installation manual for information about setting the SCSI ID for that device. The Return Installed Devices utility in the Onboard utilities can also be used to determine the SCSI addresses of peripherals on the SCSI bus. • Make sure that SCSI parity is consistently enabled or disabled on all devices on the SCSI bus. • Verify the proper installation and configuration of the host adapter and SCSI devices. • Power

ID 7 has the highest priority, and ID 0 has the lowest. Setting SCSI IDs is a two-step process: 1 Determine the ID of each device on the SCSI bus. The default ID for the AHA-1510A/20A is ID 7. To determine the IDs of disk drives, CD-ROM drives, and other devices, read their documentation and examine their switch settings or jumper settings. 2 Change the IDs (if needed) so that no IDs are duplicated on the same host adapter. We recommend the following IDs: – Leave the AHA-1510A/20A at the default

AHA-1510A/20A Series host adapters give you access to Adaptec’s ASPI (Advanced SCSI Programming Interface) family of software. This family includes device drivers that work with tape, disk, CD-ROM, WORM, and DAT devices and also with operating systems such as DOS, OS/2, UNIX, and NetWare. The ASPI software communicates with the operating system managers through the common ASPI platform. AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA AAHA-1510A/20A Series User’s Guide A AA AA ASt

2. The RAIDGuardServer icon will be displayed in the Windows notification area. Basic Configuration RAIDGuard X Client The RAIDGuard X Client is responsible for monitoring and administering the 61000/61010 remotely from any computer with Java installed. 1. Start RAIDGuardX Client either click the desktop icon or go to Start > Programs > Accusys > RAIDGuardX Client. 2. Add a controller by clicking the Adding a Controller icon. 3. Click the controller to administer and enter the password. The defa

691 South Milpitas Boulevard Milpitas, CA 95035 © 1998, Adaptec, Inc. All rights reserved. Adaptec and the Adaptec logo are trademarks of Adaptec, Inc. which may be registered in some jurisdictions. Printed in Singapore STOCK NO.: 511607-00, Rev. B BKB 12/97 t t t t SlimSCSI 1450 Adapter User’s Guide R t t t t Contents Introduction 1 Contents of Kit 1 System Requirements 1 Installing the SlimSCSI 1450 2 Updating the Windows 95 Miniport Driver 5 Using the SlimSCSI 1450 6 Hot Plugging 6 Formatting

.. Disk storage and power connection for each drive. .. Static grounding strap or electrostatic discharge (ESD) safe work area. Optional items… Battery backup module to back up cached data in the event of a power failure. LCD Control Panel for Card status and advanced configuration. 2 Familiarizing yourself with the ACS- 61100 RAID Card 1. DDRII memory connector 6. PCI-Express x 8 connector 2. I2C connector 7. Serial port connector 3. Mini SAS connectors 8. Button port connector 4. Disk access L

B FRONT COVER Print Spec. Number: 492379-00 Current Date: 3/7/94 ECN Date: 3/8/94 AMM-1570/1572 SCSI Audio Host Adapter User’s Guide AMM-1570/1572 SCSI Audio Host Adapter User’s Guide (^adapted AMM-1570/1572 User’s Guide Stock Number: 510526-00, Rev. B Page: i Print Spec Number: 492379-00 Current Date: 3/7/94 ECN Date: 3/8/94 Copyright Copyright © 1994 Adaptec, Inc. All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted i