This feature enables GSM wireless connectivity. This document describes the Cisco IOS commands and AT commands required to support V.110 on MICA modems for AS5X00 Access Servers. This MICA V.110 implementation supports 60 modems per board on the Cisco AS5300 and supports other connect standards (V.34, V.90, etc.) in addition to V.110. Modems are not dedicated to V.110 only and are allocated dynamically. On the Cisco AS5200, 30 modems per board is supported and 72 modems per board is supported on

For more information, see the “Identifying Supported Platforms” section in the “Using Cisco IOS Software” chapter. For a complete description of the modem support commands in this chapter, refer to the Cisco IOS Modem Command Reference. To locate documentation of other commands that appear in this chapter, use the command reference master index or search online. Signal and Line State Diagrams The following signal and line state diagrams accompany some of the tasks in the following sections to il

These bonded channels deliver downstream data rates in excess of 440 Mbps. That’s up to eight times faster than conventional single-channel EuroDOCSIS™ 2.0 cable modems.1 The EPC3212 uses advanced line-interface technology to provide multi-country, toll-quality, telephone service using existing in-home wiring. The EPC3212 features two RJ-11 telephone ports for voice and supports 5 REN phone loading on each phone line. Figure 1. EPC3212 EuroDOCSIS 3.0 8x4 Cable Modem with Embedded Digital Voice A

• Enter your password if prompted. show modem version Example: Router# show modem version Displays the modem firmware version and datapump version. debug modem Example: Router# debug modem Displays the modem events and state transitions. show modem version Example: Router# show modem version Displays the modem firmware version, the datapump version, and the firmware log. exit Router# exit Exits privileged EXEC mode. Troubleshooting Tips Use the following debug commands to troubleshoot the modem:

For information on new features and Cisco IOS commands supported by software for the Cisco NM-8AM-V2 and NM-16AM-V2 network modules, see the “Additional References” section on page 8. Feature History for Cisco NM-8AM-V2 and NM-16AM-V2 Network Modules Release Modification 12.3(4)XD This feature was introduced. 12.3(7)T This feature was integrated into the Cisco IOS Release 12.3(7)T on the Cisco 2600XM series and Cisco 3700 series routers. Finding Support Information for Platforms and Cisco IOS So

Para reducir el riesgo de descarga electrica, no realice ninguna tarea de mantenimiento o reparacion que no este incluida en las instrucciones de uso, a menos que este calificado para llevarla a cabo. Nota para el instalador del sistema Para este dispositivo, el blindaje o la pantalla del cable coaxial sedebe conectar a tierra tan cerca como sea practico al punto deentrada del cable al edificio. Para productos vendidos en los EstadosUnidos y Canada, esta advertencia se proporciona para que elins

Voice network modules convert telephone voice signals into a form that can be transmitted over an IP network. Voice network modules convert telephone voice signals into a form that can be transmitted over an IP network. These modules have one or two slots for installing supported interface cards. Voice interface cards (VICs) or voice/WAN interface cards (VWICs) installed in the voice network module provide physical connections to the telephony equipment or network, and are connected using the ap

BEFCMU10 Cable Modem with USB and Ethernet Connections Copyright and Trademarks Specifications are subject to change without notice. Linksys is a registered trademark or trademark of Cisco Systems, Inc. and/or its affiliates in the U.S. and certain other countries. Copyright © 2003 Cisco Systems, Inc. All rights reserved. Other brands and product names are trademarks or registered trademarks of their respective holders. WARNING: This product contains chemicals, including lead, known to the S

This information is often required when contacting Cisco support or to ensure that all appliances in a cluster are running the same software version. To obtain version information from the ACE XML appliance: Step 1 Log into the appliance shell as the root user. Step 2 In the Main Menu, choose the Advanced Options menu item. The Advanced Options menu appears. Step 3 Choose the Version Information menu item. The release identifier string appears as a banner at the top of the screen. In the center

To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions, unless you are qualified to do so. Notice a l’attention des installateurs de reseaux cables Les instructions relatives aux interventions d’entretien, fournies dans la presente notice, s’adressent exclusivement au personnel technique qualifie. Pour reduire les risques de chocs electriques, n’effectuer aucune intervention autre que celles decrites dans le mode d'emploi et les