For additional modem configuration options, please refer to the Raven-E iDEN Users Guide for TELUS. Note: If the SIM card was pre-installed by AirLink, there is nothing more you need to do. Skip to the Hardware section and/or to the DUN instructions, if you need Dial-Up Networking. Installing the SIM To install the SIM, you will only need a small phillips head screw driver. 1. Opening the Case a. Unplug the Raven-E’s power and all cables. b. Using a small phillips head screw driver, remove the s

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense. CE Mark Warning This is a Class A product. In a domestic environment, this product may cause radio interference, in which cas

Installation The site where you install the Switch stack may greatly affect its performance. Use the following guidelines when installing the Switch. • Install the Switch in a cool and dry place. See Specifications for the acceptable temperature and humidity operating ranges. • Install the Switch in a site free from strong electromagnetic field generators (such as motors), vibration, dust, and direct exposure to sunlight. • Leave at least 10 cm of space at the front and rear of the hub for venti

Unpacking Open the shipping carton and carefully unpack the contents. The carton contains the following items: • One the 16-port 10/100Mbps Fast Ethernet Switch • One external power adapter • Four rubber feet to be used for shock cushioning • This User's Guide AirLink+ 16-Port 10/100Mbps Fast Ethernet Switch (Desktop) User Guide If any item is missing or damaged, contact your local reseller for replacement. Installation The site where you install the Switch may greatly affect its performance. Wh

Start your Web browser and type in the Address field. This address is the default private IP of your router. Note If the router’ s LAN port has been changed with new IP address, enter the new IP address instead. 2. When prompted with the following screen, leave the username empty and enter the default password of admin. Wireless Broadband Router User Manual After successful login, you will be able to see the Wireless Broadband Router’ s web-based configuration utility. From now on the Wireless B

•Outgoing Network Connection: Enables an outgoing connection to the specified host. •Outgoing Telnet Connection: Enables an outgoing telnet connection to the specified host. •Modem Service Options: When Modem Service is selected, you may also configure the Source TCP Port. In most cases, the value used for the source port is arbitrary and you can leave this field set to 0 for “any”. However, if your server or firewall has specific requirements you may specify an explicit source port number in th

© Copyright AirLink Communications, Inc, 1993-2004. All rights reserved. Please send comments to: email: pubs@AirLink.com Fax: 510-264-5422 Phone: 510-264-5400 Post: AirLink Communications, Inc. Attention: Technical Publications Dept. 3159 Corporate Place Hayward, CA 94545 Important Notice Because of the nature of wireless communications, transmission and reception of data can never be guaranteed. Data may be delayed, corrupted (i.e., have errors) or be totally lost. Although significant delays

Rx Div) on the back of the Raven X. Use of receive diversity for EV-DO is optional. Data transmission and reception will not be adversely affected if it is not used. Connecting Power Your Raven X can be used with either DC (available in most automobiles) or 110 AC (standard US wall power) with the appropriate power adapter (available from AirLink). The power cable positive lead should be connected to the battery or power source positive terminal. The power cable negative lead should be connected

AirLink Communications, Inc. August 9, 2001 Page 7 AirLink Raven II CDPD Modem 16. Select the Connection tab and set the Connection Preferences to: Data bits: 8 Parity: None Stop bits: 1 Uncheck (disable) “Wait for dial tone before dialing.” 17. Select Port Settings. You should see the Advanced Port Settings dialog. Check the box for Use FIFO buffer if appropriate. If the button is enabled, it is probably appropriate. 18. Select OK. You should go back to the Connection tab. 19. Select Advanced.