Argument: None. Possible value: None. Example: None. save start Syntax: save start Description: To save the current configuration as the startup configuration. When you enter this command, the CLI will save your current configuration into the non-volatile FLASH as the start up configuration. Argument: None. Possible value: None. Example: GSM-16T2SFP# save start Saving start... Save Successfully GSM-16T2SFP# 120 Alloy Computer Products Pty Ltd Copyright ©2006 GSM Series User Manual save user Synt

4 1.1 Managing The Switch ................................................................................................. 6 1.2 Configuration of the Switch ....................................................................................... 7 2 Configuration .............................................................................................................................. 8 2.1 Port Status ...........................................................................................

Harsh temperature conditions, vibration, dust, etc. all put higher demands on the quality and reliability of your networking equipment. To survive harsh industrial environments, Alloy provides you with the RNS5/8 Series Industrial 5-port/8-port 10/100Mbps Ethernet Switches. The RNS5/8 Industrial switch is a cost-effective solution ideal for your industrial applications in harsh environments. The RNS5/8 not only gives you high speed data transmission over an Ethernet network, but also provides re

Introduction ............................................................................................................... 2 2. Safety Notification .................................................................................................... 3 3. Hardware Installation................................................................................................ 4 4 Web Management Settings ....................................................................................... 5 4.1. Set

Dry weather conditions or walking across a carpeted floor may cause you to acquire a static electrical charge. To protect your switch, always: • Touch the metal chassis of your computer to ground the static electrical charge before you handle the switch. • Pick up the switch by holding it on the left and right edges only. Electronic Emission Notices Federal Communications Commission (FCC) Statement This equipment has been tested and found to comply with the limits for a Class A computing device

OVERVIEW OFTHE POEGEM12T2SFPSNMPMANAGED POE SWITCHES........................2 1.2. CHECKLIST .......................................................................................................................4 1.3. FEATURES ........................................................................................................................4 1.4. OVERVIEW OF THE POEGEM12T2SFP SWITCH................................................................5 1.4.1. User Interfaces on the Front Panel (

OVERVIEW OF GSM SERIES SNMP MANAGED SWITCHES ..................................................2 1.2. CHECKLIST .......................................................................................................................3 1.3. FEATURES ........................................................................................................................4 1.4. OVERVIEW OF GSM SERIES SWITCHES .............................................................................5 1.4.1. User Int

When you use an Ethernet cable to connect other devices, such as computers, switches or hubs, pin 1, 2, 3, and 6 of the 8-pin RJ45 connector are used to communicate with the connected devices. Pin1, 2, 3, and 6’s signals are converted by the MDI-X function, as shown in Table 2. Pin MDI-X Signals MDI Signals 1 RD+ TD+ 2 RD- TD- 3 TD+ RD+ 6 TD- RD- Table 2 Cabling The cable connection between the RNS5/8 and the attached devices (switches, hubs, workstations, etc.) must be less than 100 meters (328

Switches supporting both traditional 10Mbps Ethernet and 100Mbps Fast Ethernet are also ideal for bridging between the existing 10Mbps networks and the new 100Mbps networks. Switching LAN technology is a marked improvement over the previous generation of network bridges, which were characterised by higher latencies. Routers have also been used to segment local area networks, but the cost of a router, the setup and maintenance required make routers relatively impractical. Today switches are an id

(Standard Operating) -40. to 70. (Non-Operating) Humidity:5% to 95% (Non-condensing) Vibration: IEC 68-2-36, IEC 68-2-6 Shock: IEC 68-2-29 Drop: IEC 68-2-32 Warranty Limited lifetime warranty 4 DC output redundant power supply connectors (Supports max. power output 150W/12V per port) 1 port 10GBase-LR module with XFP connector Stacking cables length 30cm/1.3m for inter switch stacking connection 10GE XENPAK Optical Transceiver (Link length: 10km; Laser: 1310nm) Small Form Factor Pluggable (Dista