McDowell Rd. ..............602 At 8-1332 ARKANSAS; Little Rock 72201, 519 West Seventh St.......501 FR 2-3040 CALIFORNIA; Anaheim 92802, 1235 So. Euclid Ave.........714 772-4050 Los Angeles 90007, 2432 S, Broadway..........................213 Rl 9-0371 Oakland 94606, 1107 E. 14th St...................................415 ТЕ 4-5944 Sacramento 95814, 1915 Seventeenth St.....................916 444-3188 San Diego 92105, 3811 El Cajon Bivd...........................714 280-3331 Santa Clara 950

No. 36070 Sanding Frame For the 4023 & 4024 ELU Belt Sanders BiACK&DECKER Instructions 1. Turn Off And Unplug Sander. 2. Remove the front pivot bar from the sanding frame and remove the hex nut, flat washer, pivot crank and spring, (see Figure 1) 3. Insert the pivot bar through the sander FROM THE RIGHT SIDE as shown in Figure 2. Examine the figure closely to determine the position of the spring and fiat washer. 4. With the threaded end of the pivot bar extending from the left side of the s

Lubrication MASTER MECHANIC tools are properly lubricated at the factory and are ready for use. Cleaning Blowing dust and grit out of the motor housing using compressed air is a necessary regular maintenance procedure. Dust and grit containing particles from metal grinding often accumulate on interior surfaces and could create an electrical shock hazard if not frequently cleaned out. CAUTION: Never use solvents or other harsh chemicals for cleaning the nonmetallic parts of the tool. Use clean, d

V ..........................volts A ........................amperes Hz ........................hertz W ......................watts min ......................minutes ......................alternating current ....................direct current no ......................no load speed ........................Class II Construction ........................earthing terminal ........................safety alert symbol .../min ................revolutions or reciprocations per minute CAT. NO. FS500,FS550,F

Spindle Lock Button TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. (See Figure 1) In order to prevent the spindle of the tool from rotating while installing or removing accessories, a spindle lock button has been provided in the gear head of the machine. To lock the spindle, depress and hold the lock button. NEVER DEPRESS THE SPINDLE LOCK BUTTON WITH THE TOOL RUNNING OR COASTING. Attaching and Removing Polishing Pads (FIGURES 4 & 5) TURN OFF TOOL AND DISCONNECT FROM POWER SUPPLY. To attach pad,

IN MOST CASES, A BLACK & DECKER REPRESENTATIVE CAN RESOLVE YOUR PROBLEM OVER THE PHONE. IF YOU HAVE A SUGGESTION OR COMMENT, GIVE US A CALL. YOUR FEEDBACK IS VITAL TO THE SUCCESS OF BLACK & DECKER’S QUALITY IMPROVEMENT PROGRAM. KEY INFORMATION YOU SHOULD KNOW: • Always wear eye protection. • Make sure tool rests, spark guards, and eye shields are firmly secured before tool is engaged. SAVE THIS MANUAL FOR FUTURE REFERENCE. VEA EL ESPANOL EN LA CONTRAPORTADA. INSTRUCTIVO DE OPERACION, CENTROS DE

The following grinders and sanders are described in this manual. D28474 D28493 D28494 D28497 D28499 7" Angle Grinder 8,000 rpm 9" Angle Grinder 5,000 rpm 7"/9" Angle Grinder 6,000 rpm 7"/9" Angle Sander 6,000 rpm 7"/9" Angle Grinder 6,000 rpm Components A. Trigger Switch C. Spindle Lock E. Spindle G. Rubber Bumper A B D E F C G Features SWITCH B. Lock On Button D. Side Handle F. Soft Mount The tool is controlled by a trigger switch (A). A lock-on button (B) provides increased comfort in extended

(See Fig, 2) 3. Insert abrasive paper under the clamp, pull up on lever and lock into place. (Fig. 3) 4, Stretch paper over backing pad and insert under the opposite clamp in the same way. «SPRING CIAMP SANDING LEVER It is not necessary to exert a lot of pressure on the tool when sanding horizontally. A slight amount of pressure (just to control the tool) is usually sufficient to ensure satisfactory results. Any excess will reduce its efficiency. In order tp obtain an optimum finish, it is

This means that it is constructed throughout with TWO separate “layers” of electrical insulation or one DOUBLE thickness of insulation between you and the tool’s electrical system. Tools built with this insulation system are not intended to be grounded. As a result, your Drill is equipped with a two-prong plug which permits you to use extension cords without concern for maintaining a ground connection. NOTE DOUBLE-INSULATION does not take the place of normal safety precautions when operating t

Be sure switch is off when plugging in. 17 OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 18 STAY ALERT. Watch what you are doing Use common sense. Do not operate tool when you are tired. ' 19 CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving p