Suite 300, Richmond Hill, ON, L4B 1M4. Information en ce qui concerne l'operation sure et correcte de cet outil est disponible des sources suivantes: • Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851 ou en ligne • National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201 • American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 -ANSI 01.1 Safety Requirements for Woodworking Machines • U.S. Department of Labor regulations MESURES DE

Always follow basic safety precautions to reduce the risk of personal injury. Improper operation, maintenance, or modification of tools or equipment could result in serious injury and property damage. Our tools and equipment are designed for certain applications. DO NOT modify and/or use this product for any application other than that for which it was designed. If you have any questions relative to its application DO NOT use the product until you have written Delta Machinery and we have advised

Record these numbers in the spaces below and retain for future reference. Model No. ______________________________________ IMPORTANT Please make certain that the person who is to use this equipment carefully reads and understands these instructions before starting operations. ESPANOL: PAGINA 17 FRANCAISE : PAGE 33 MODEL 340 Double Insulated Finishing Sander Type ___________________________________________ Serial No. _______________________________________ Copyright © 2005 Porter-Cable Part No. A

8. CLEAN UP ALL REMOVED PAINT and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surfaces where paint or dust is clinging. DO NOT SWEEP, DRY DUST OR VACUUM. Use a high phosphate detergent or trisodium (TSP) to wash and mop areas. 5 901397 - 09-30-01.qxd 2/13/02 2:11 PM Page 6 9. AT THE END OF EACH WORK SESSION put the paint chips and debris in a double plastic bag, close it with tape or twist ties and dispose of properly. 10. REMOVE PROTECTIVE CLOTHING an

English English 4-1/2" Cutting Wheels Sanding Discs 4-1/2" Sanding Flap Discs Type 1 guard backing flange abrasive cutting wheel clamp nut Type 1 guard backing flange diamond cutting wheel clamp nut rubber backing pad sanding disc threaded clamp nut hubbed sanding flap disc backing flange non-hubbed sanding flap disc threaded clamp nut Type 27 guard Type 27 guard 1. Open the guard latch (M). Align N the lugs (N) on the guard with the slots (O) on the gear case. 2. Push the guard down until the g

Allow the grinder to run up to full speed before touching the work surface. Lift the tool from the surface before turning the tool off. Allow the tool to stop rotating before putting it down. PADDLE SWITCH (D28402, D28402N) CAUTION: Before connecting the tool to a power source depress and release the paddle switch (A) once [D28402: without depressing the lock-on button (J)] to ensure that the switch is off. Depress and release the paddle switch as described above after any interruption in power

Allow the tool to stop rotating before laying it down. WARNING: Do not use edge grinding/cutting wheels for surface grinding applications because these wheels are not designed for side pressures encountered with surface grinding. Wheel breakage and injury may result. 9 SURFACE FINISHING WITH SANDING FLAP DISCS 1. Allow the tool to reach full speed before touching work surface. 2. Apply minimum pressure to work surface, allowing operate at high speed. Sanding rate is greatest when operates at hig

3. Screw the threaded clamp nut onto the spindle (D). 4. Rotate the spindle by hand while pressing the spindle lock fully until it has found its locking location and holds the spindle still (E). 5. Firmly tighten the threaded flange with the supplied hex wrench (F). Mounting Edge Cutting Wheels (Fig. 2) Type 27 Edge cutting wheels are available as optional accessories. Before fitting a cutting wheel, unplug tool from the power source. 1. Locate the inner clamp nut (A) on the machine spindle (B).