valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
OPERATING TIPS OPERATING POSITION • While vacuuming or blowing debris, hold the unit with the muffler side facing away from your body and clothes (see OPERATING POSITION below). • To reduce the risk of hearing loss associated with sound level(s), hearing protection is required. • To reduce the risk of injury associated with contacting rotating parts, stop the engine before installing or removing attachments. Do not operate without guard(s) in place. • Operate power equipment only at reasonable hours-not early in the morning or late at night when people might be disturbed. Comply with times listed in local ordinances. Usual recommendations are 9:00 a.m. to 5:00 p.m., Monday though Saturday. • To reduce noise levels, limit the number of pieces of equipment used at any one time. • To reduce noise levels, operate power blowers at the lowest possible throttle speed to do the job. • Use rakes and brooms to loosen debris before blowing. • In dusty conditions, slightly dampen surfaces or use a mister attachment when water is available. • Conserve water by using power blowers instead of hoses for many lawn and garden applications, including areas such as gutters, screens, patios, grills, porches, and gardens. • Watch out for children, pets, open windows, or freshly washed cars. Blow debris away safely. • Use the full blower nozzle extension so the air stream can work close to the ground. • After using blowers and other equipment, CLEAN UP! Dispose of debris in trash receptacles. -9 Blower Vacuum \ BEFORE STARTING ENGINE ,'_ WARNING: Be sure to read tile fuel information in the safety rules before you begin. If you do not understand the safety rules, do not attempt to fuel your unit. Call 1-800-235-5878. FUELING ENGINE _&WARNING: Remove fuel cap slowly when refueling. This engine is certified to operate on un leaded gasoline. Before operation, gaso line must be mixed with a good quality synthetic 2-cycle air-cooled engine oil. We recommend Craftsman brand synthetic oil. Mix gasoline and oil at a ratio of 40:1. A 40:1 ratio is obtained by mix ing 3.2 ounces of oil with 1 gallon of un leaded gasoline. Included with this blow er is a 3.2 ounce container of oil. Pour the entire contents of this container into 1 gallon of gasoline to achieve the prop er fuel mixture. DO NOT USE automotive oil or boat oil. These oils will cause en gine damage. When mixing fuel, follow instructions printed on container. Once oil is added to gasoline, shake container momentarily to assure that the fuel is thoroughly mixed. Always read and fol low the safety rules relating to fuel before fueling your unit. IMPORTANT Experience indicates that alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. Acidic gas can damage the fuel system of an engine while in storage. To avoid engine problems, empty the fuel system before storage for 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Use fresh fuel next season. Never use engine or carburetor cleaner products in the fuel tank or permanent damage may occur. Fuel stabilizer is an acceptable alternative in minimizing the formation of fuel gum deposits during storage. Craftsman brand oil is already blended with fuel stabilizer. See the STORAGE section for additional information. HOW TO STOP YOUR ENGINE • Release the throttle trigger. • Push and hold the STOP switch in the STOP position until the engine stops. HOW TO START YOUR ENGINE WARNING: You MUST make sure the tubes are secure before using the unit. • Fuel engine. Move at least 10 feet (3 meters) away from the fueling site. • Hold the unit in the starting position as shown. Make sure the blower end is directed away from people, animals, glass, and solid objects. STARTING POSITION Blower A dBkWARNING: When starting engine, hold the unit as illustrated. Do not set unit on any surface except a clean, hard area when starting engine or while engine is running. Debris such as gravel, sand, dust, grass, etc. could be picked up by the air intake and thrown out through the discharge opening, damaging the unit or property, or causing serious injury to bystanders or the operator. -10 STARTING A COLD ENGINE 1. Move the throttle position lever (cruise control) to the idle position. Throttle Position Lever (Cruise Control) 2. Slowly press the primer bulb 6 times. 3. Move the start lever to the START position. Starter Handle Lever Primer / Bulb 4. This unit has the Sim-pul-" starting system. You do not have to pull the starter rope handle sharply or briskly. Pull starter rope handle 5 times with a controlled and steady motion (no more than 3 times above 90°F). If engine starts and runs prior to 5 pulls, allow engine to run for 5 seconds; then, fully squeeze the throttle trigger to disengage the starting system (start lever returns to RUN position). Steps 5 and 6 are not necessary. 5. Fully squeeze t...
Questo manuale è adatto anche per i modelli :Sistemi di ventilazione - 79476 (1.59 mb)