TWIN LINE TAP FEED HEAD KIT ITEM PART NO. DESCRIPTION _ 6-8037 KIT, .095 L.H. Twin Line Tap Feed Head (Includes Items 1 thru 7) 1 4-2081 HEAD, Twin Line Bump, L.H. (Includes Items 2 thru 6) 2 4-2073 ASSEMBLY, Hub 3 4-2074 SPRING 4 4-2082 ASSEMBLY, Spool & Line 5 2-1971 KNOB, Bump 6 4-2083 BOLT, Slotted Hex Flange, L.H. 7 1-8784 CARD/Parts (Not Illustrated) 1 5 Section I - TRIMMER ACCESSORIES BRUSH BLADE CONVERSION KIT WITH METAL SHIELD 16 Section I - TRIMMER ACCESSORIES BRUSH BLAD

• To remove turbo, reverse the installation steps. Recommended Accessories • Front counterweight is recommended when using rear-mounted grass catcher. • On slopes over 17.6% (10°), use two rear wheel weights in addition to front counterweight. Always mow up and down the face of slopes, never across the face. Never mow on slopes greater than 30% (16.7 degrees) NOTE: In these instructions, “left” and “right” are referred to as seen from the operating position. 1 2 Installation Instructions 54”Turb

Hinge & Deflector (Deflector Removed for Clarity) D. Tapered Spacer E. Original Lockwasher and Nut F. 5/8 x 1 Cylinder Spacer A BC Figure 7. Connect Deflector Spring A. Spring Anchor B. Spring C. Deflector Arm 6 7 54”Turbo Blower Installation Instructions FRONT Install Turbo Blower 1. Install the turbo blower assembly. Insert the tapered spacers (B, Figure 8) through the bottom of the blower housing (A). 2. Install one spring clip (C) on both tapered spacers (B). 3. Hook the bottom of the turbo

(Includes Items 44 thru 54) LINE, Fuel GROMMET, Fuel Line CUP, Fuel Line FILTER ASS'Y, Fuel (Includes items 48, 49, 64, 65, 66, 68) CLIP SLEEVE, Gov CAP ASS’Y, (Includes Items 51 thru 54) CAP, Fuel GASKET HOLDER VALVE, Breather MOUNT, Fan-Wheei SCREW, M5x12mm PHCR (3) MOUNTING PLATE, Engine DAMPER,Eng.Mtg.Plate(4) PAD, Fuel Tank(4) SEAL, Eng. Mtg. Plate (3) BRACKET SWITCH, Stop SCREW FELT (2) RING SCREEN SCREW BODY, Fuel Filter ENGINE, COMPLETE(lncludes items 2 thru 42 & 61, 62, 6

Always mention the model and serial number as found on the nameplate attached to the unit. The information in the parts section furnished with your blower is subject to change. Up-to-date parts manuals covering your blowers. For the nearest SNAPPER dealer, check the yellow pages under the heading LAWN-MOWERS. FIG. 8 - AIR CLEANER DETAIL AIR CLEANER - SERVICE EVERY 25 HOURS Every 25 hours or more frequently if operating under extremely dusty or dirty conditions, service the air cleaner as foll

• Never attempt to make major repairs on this unit unless you have been properly trained. Improper service procedures can result in hazardous operation, equipment damage and voiding of manufacturer’s warranty. 4 3 unit assembly Note: Please refer to Parts List for correct part identification and placement. FRONT WHEEL ASSEMBLY • Attach left and right caster brackets to caster wheel using 3/8-18 x 2-1/4 bolt and lock nut. Insert bolt through hole in bracket. Place caster wheel onto bolt. Place ot

7078092 (I.R. - 09/14/04) Text Box: McDonough, GA 30253 USA Text Box: European Extreme Series Walk-Behind Leaf Blower Series 1 Text Box: Text Box: Text Box:

7043324 (I.R. - 02/28/05) (Part # 7085927) 1 preliminaries Congratulations! You have just purchased one of the finest pieces of outdoor power equipment on the market today. If properly cared for, your new blower will provide years of dependable service. Please read and follow this instruction manual carefully in order to get the most out of your new equipment. As you carefully unpack your unit, you will find the following items: 1 Blower Unit 1 Handle Assembly including: 1 – Upper Handle with fo

Be sure all safety features are attached, adjusted properly and functioning properly. • Never operate with the discharge deflectors removed or altered. • Do not change the engine governor setting or over speed the engine. • Stop on level ground, shut off engine before leaving the operator’s position for any reason. • Stop equipment and inspect impeller blades after striking objects or abnormal vibration occurs. Make necessary repairs before resuming operations. • Keep hands and feet away intake

• Keep hands, feet and clothing away from rotating parts. Never place your feet or hands in path of discharge. • Use proper discretion in selecting your debris removal pattern, especially on uneven terrain. Avoid steep hills, especially if surface is wet. Do not travel straight down slopes exceeding 14 degrees. If tires begin to slip when climbing a slope, the grade is too steep for safe operation. Angle the unit to a less steep slope until tires stop slipping and traction is regained. • Be keen