valutazioni - 3, GPA: 4.3
(
)
)
|
Facilità d'uso
L Check the paper size shown on the display panel. 134 dAdding Staples d Adding Staples Important . Stapling failures or jams may occur if you use a staple cartridge other than that recommended. Reference For details about the type of finisher, see p.19 “External Options”. 500-Sheet Finisher ZEWJ000E ZEWJ010E ZEWJ020E ZEWJ030E • 1: Open the side cover. • 2: Remove the cartridge. • 3: Take out the empty refill in the direction of the arrow. • 4: Push in the new refill until it clicks. • 5: Pull out the ribbon. ZEWJ040E 135 Troubleshooting ZEWJ050E • 6: Reinstall the cartridge. • 7: Close the side cover. 1000-Sheet Finisher • 1: Open the front cover of the finisher, and then pull out the staple unit. • 2: Hold the green lever, and then gently pull out the cartridge. ZGJS801E ZGJS802E ZGJS803E • 3: Hold both sides of the cartridge. • 4: Pull up the upper unit of the cartridge. ZGJS804E • 5: Take out the empty refill in the arrow direction. ZGJS805E • 6: Align the arrows on the new refill with those on the cartridge, and then push in the refill until it clicks. 136 dAdding Staples • 7: Gently push down the upper unit into the cartridge. ZGJS806E ZGJS807E • 8: Pull out the ribbon. • 9: Hold the green lever while pushing in the cartridge until it clicks. • 10: Push back the staple unit, and then close the front cover of the finisher. ZGJS808E 137 Troubleshooting Removing Jammed Staples Note . Curled paper may cause staples to jam. To avoid this, turn copy paper over in the tray. If there is no improvement, change to a stiffer copy paper. . When the 500-sheet finisher is installed, after removing jammed staples, staples will not be ejected the first few times you try to use the stapler. Reference For types of finisher, see p.19 “External Options”. 500-Sheet Finisher ZEWJ000E ZEWJ010E ZEWJ106E ZEWJ107E ZEWJ108E • 1: Open the side cover. • 2: Remove the cartridge. • 3: Open the face plate. • 4: Remove the jammed staples. • 5: Reinstall the cartridge. • 6: Close the side cover. 138 Removing Jammed Staples 1000-Sheet Finisher ZGJS801E ZGJS802E ZGJS813E ZGJS814E ZGJS815E ZGJS864E • 1: Open the front cover of the finisher, and then pull out the staple unit. • 2: Hold the green lever while gently pulling out the cartridge. • 3: Open the cartridge's face plate. • 4: Remove any jammed staples. • 5: Pull down the cartridge's face plate until it clicks. • 6: Hold the green lever while pushing in the cartridge until it clicks. • 7: Push back the staple unit, and then close the front cover of the finisher. Troubleshooting Replacing the Stamp Cartridge When the stamp begins to fade, replace the cartridge. Note . This stamp cartridge is used for facsimile and scanner functions. . Use the cartridge specified for this machine. . Do not attempt to put ink into the cartridge. Doing so will result in leakage. . Be sure not to dirty your fingers with ink from the cartridge. A Open the ADF unit. ZEXH070J B Open the stamp cover. ZGNH011J C Pull out the old stamp cartridge. Tap the cartridge lock lever several times. The cartridge will eject. Then remove the cartridge, while pushing the lock lever. ZEXH080J D Insert the new stamp cartridge. Insert the cartridge until the metal parts are no longer visible. ZFGH090E E Press the stamp cover back in until it clicks. ZEXH100J F Close the ADF unit. 140 Dos and Don'ts RWARNING: • Keep the machine away from flammable liquids, gases, and aerosols. A fire or an electric shock might occur. RCAUTION: • Unplug the power cord from the wall outlet before you move the machine. While moving the machine, you should take care that the power cord will not be damaged under the machine. Important . Do not turn the power off while the On indicator is lit or blinking. Doing so may damage the hard disk. . Before unplugging the power cord or turning off the main power switch, make sure remaining memory space is at 100%, as shown on the display. See p.26 “Turning Off the Power” and p.26 “Turning Off the Main Power”. • When you use this machine for a long time in a confined space without good ventilation, you may detect an odd smell. To keep the workplace comfortable, we recommend that you keep it well ventilated. • Do not touch areas on or around the fusing unit. These areas may become hot • After scanning originals continuously, the exposure glass may become warm—this is not a malfunction. 7. Remarks • The area around the ventilation hole might feel warm. This is caused by exhaust air and is not a malfunction. • When the machine is not in use and in stand-by mode, you may hear a small noise inside. This is caused by the image stabilization process and is not a malfunction. • Do not turn off the power when the machine is in operation. • The machine might not produce good copy images if condensation forms inside as a result of rapid temperature change. • Do not open the covers of the machine when it is in operation. If you do, misfeeds might occur. • Do not move the machine when the power is on. • If you operate th...
Questo manuale è adatto anche per i modelli :scanner / copiatrice / MFP - LD230 (2.81 mb)