Operator’s Manual 9 Horse Power SNOW THROWER Model No. 247.88790 • SAFETY • ASSEMBLY • OPERATION • MAINTENANCE • PARTS LIST ® 06/13/2006 FORM NO. 769-02587 TABLE OF CONTENTS Warranty Statement..................................Page 2 Safety Labels............................................Page 3 Safe Operation Practices .........................Pages 4 Assembly..................................................Pages 6 Operation..................................................Pages 9 Maintenance.

Note, install the rear bolt first for easier alignment. 2. Tighten bolts securely with a wrench. 3. Lift up folding handle to align it with lower handle and tighten the wing knobs securely as shown in Figure 3. The snow thrower is now ready for operation once the fuel tank has been filled with the properly mixed gasoline and two cycle oil. Figure 1. Assembly of Discharge Chute A. Discharge Chute D. Nuts B. Carriage Bolts E. Rotating Ring C. Washers A B C D E Figure 2. Handles A. Handle B. Wing K

44" Blower Assy. 50" Blower Assy. Mfg. No. 1691867 Mfg. No. 1691868 Mfg. No. 1692030 Mfg. No. 1692626 General RECOMMENDED ACCESSORIES...............................................................................................................................1 SAFETY DECALS.........................................................................................................................................................1 SAFETY RULES....................................................

For close snow removal on a smooth surface, raise skid shoes higher on the auger housing. Use a middle or lower position when the area to be cleared is uneven, such as a gravel driveway NOTE: If you choose to operate the snow thrower on a gravel surface, keep the skid shoes in position for maximum clearance between the ground and the shave plate. To adjust the skid shoes: Loosen the four hex nuts (two on each side) and carriage bolts. • • 1. Figure 7 CaUTion It is not recommended that you operat

746-04229 Clutch Cable, Wheel, 44.95” 28. 790-00289A Plate, Cover 29. 748-0190 Spacer, .508 ID x .75 OD x .68 30. 756-0625 Roller, Cable 31. 790-00096 Front Guide Bracket, Auger Cable 32. 790-00180A Frame 33. 790-00206A Guide Bracket, Auger Cable 34. 790-00207A Guide Bracket, Drive Cable 35. 790-00316 Cover, Frame 36. 634-04148A Wheel Assembly - RH 634-04147A Wheel Assembly - LH 37. 731-04873 Spacer, 1.25 x .75 x 3.0 Ref. No. Part No. Description 38. 738-04168 Axle, .75 x 22” 39. 735-04099 Plug,

H. Voltmeter (Models with air cooled engines) Shows the voltage being produced by the charging circuit and battery. I. Coolant Temperature (Models with liquid cooled engines) Shows the engine coolant temperature. J. Irregular Voltage (Models with liquid cooled engines) Indicates that the voltage being produced by the charging system and the battery is higher or lower than normal levels. K. Glow Plug Light (Models with diesel engines) Indicates that the glow plugs are heating. Leave the key in th

* Cover—on pre-printed two-tone “Swash” stock. Press: * Body—1-color, 2-sided * Cover imprint —1-color, 1-sided Bindery: * Saddle Stitch, Face Trim, 3-Hole Drill * Face Trim COVERS: * This file contains several manuals, which differ only in their covers. * Covers are all present at the beginning of this file. * Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover. • Check the front cover for the individual part number (typically a 171xxxx number). BODY: • The body of

21 HOW TO REMOVE THE SNOW HOOD To access the spark plug, the snow hood must be removed as follows: 1. Remove the choke control knob (see Figure 21). 2. Remove the safety key. 3. Remove the mounting screws (see Figure 22). 4. Slowly remove the snow hood. Make sure that the primer button hose and the Ignition wire are not disconnected. 5. The spark plug can now be accessed. 6. To install the snow hood, first make sure that the primer button hose and the ignition wire are connected. 7. Mount the sn

* Cover—on pre-printed two-tone “Swash” stock. Press: * Body—1-color, 2-sided * Cover imprint —1-color, 1-sided Bindery: * Saddle Stitch, Face Trim * Face Trim COVERS: * This file may contain several manuals, which differ only in their covers. * Covers are all present at the beginning of this file. * Back cover for a particular manual is the page IMMEDIATELY AFTER the front cover. • Check the front cover for the individual part number (typically a 171xxxx number). BODY: • The body of the manual

486.24837 DO NOT RETURN TO STORE For Missing Parts or Assembly Questions Call 1-866-576-8388 FOR TRACTORS WiTH MODEL NUMBERS BEGiNNiNG WiTH 917. CAUTION: ,, Safety Before using this product, read ,, Assembly this manual and follow all Safety Rules and Operating Instructions. ,, Operation ,, Maintenance ,, Parts Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A. PRINTED IN U.S.A. FORM NO. 41361 rev. (07/30/10) ACCESSORIES ............................................................... 2 SER