Inspect tool cords and air hoses periodically and, if damaged, have them repaired by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times. 10. Disconnect air supply. Disconnect air hose when not in use. 11. Remove adjusting keys and wrenches. Check that keys and adjusting wrenches are removed from the tool or machine work surface before plugging it in. 12. Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you

Please confirm it before installation. 2. If the car interior is extremely hot, as after being parked in the sun, do not use the player until the car has been driven fora while to cod off the interior. 3. Press the OPEN button to flip down the front panel (see fig.1), Slide the guide knob to remove the right side first, then take away the front panel, (see fig.2) and put it in the protective case (see fig.3) for safe keeping. 4. Install the front panel back into its bracket and then push it

Other people in the work area must also wear ANSI approved impact safety goggles. Warning! Make sure the Nailer is not attached to the air hose whenever loading the tool. 1. Press the Magazine Latch (3-8) up and slide the Magazine Side Cover (3-1) back. 2. Holding the nailer with the nose pointing slightly down, insert the brad nails into the Magazine Side Cover (3-1), letting the pointed end ride on the rail of the Magazine Side Cover (3-1). 3. After the Nails reach the nose of the tool, close

Orient a strip of nails with the points down, and drop the strip of nails into the Magazine (part #71). (See Figure C.) 4. Slide the strip of nails forward in the Magazine (part #71). NOTE: The Magazine will hold 60, 10 gauge nails. (See Figure C.) 5. Unlatch the Feeder Shoe (part #52), and allow the Feeder Shoe to slide forward against the strip of nails. (See Figure C.) OPERATION NOTE: For additional references to the parts listed below, refer to the Assembly Diagram on page 11. 1. Adjust the

Testing the Double Trigger Safety Mechanism Warning: Even though the nailer should be empty during this procedure, ALWAYS point the nailer at a piece of scrap wood when testing. 1. Make sure the tool is disconnected from the power supply. 2. Completely empty the magazine of nails. 3. The Nailer should not fire if the second trigger Safety Trigger (123) Trigger (125) Figure 1 is not pulled. 4. Check that the Trigger (125) and the Safety Trigger (123) move freely, without sticking see Figure 1. 5.

Note: If you are not using an automatic oiler system, before operation, add a few drops of Pneumatic Tool Oil to the airline connection. Add a few drops more after each hour of continual use. 2. Set the air pressure on your compressor to between 70-90 PSI. Do not exceed the maximum air pressure of 100 PSI. 3. Check the air connection for leaks. Disconnect from the air source. SKU 90399 For technical questions, please call 1-800-444-3353. Page 4 Operation (continued) Assembly - Attaching the Arm

19. Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users. Never allow children to come in contact with this product. 20. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with a sharp cutting edge are less likely to bind and are easier to control. Do not use a damaged tool. Tag damaged tools “Do not use” until repaired. 21. Check for misalignment or binding of moving parts, breakage of par

Read warning labels if taking prescription medicine to determine if your judgement or reflexes are impaired while taking drugs. If there is any doubt, do not operate the tool. 19. Use proper size and type extension cord. If an extension cord is required for the air compressor, it must be of the proper size and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt and catch fire, or cause electrical damage to the tool. Check your compressor’s

ASSEMBLY AND OPERATING INSTRUCTIONS NOTE: For additional information regarding the parts listed in the following pages, refer to the Assembly Diagram on page 14. Apply Pressure Here Power Cord (7) Safety (21) Nose (19) Trigger (13) Magazine (22) Lever (29) Fastener Window FIGURE 1 Warning: This Nailer / Stapler is not suited for nailing or stapling into concrete, masonry, bricks, or metal. Warning! Do not fire if Brad Nails or Staples are jammed in the Nose (19) section. Unplug the unit and foll

If there are only a few nails remaining, simply load another strip of nails into the Magazine behind the few remaining nails and the Nailer will be ready for further use. Rev 11/06 REV 06/05 SKU 91044 For technical questions, please call 1-800-444-3353. Page 6 Operation (continued) Warning! Disconnect the Nailer from the air compressor whenever loading or servicing. FIGURE 1 FIGURE 2 Exhaust Cover (4) Tab (70) Trigger (47) Air Inlet (90) Latch (83) Safety (41) Magazine (76) FIGURE 3 FIGURE 4 Ang