Sit on the driver seat. NOTE: The machine will not traverse if the operator is not properly seated. 2. Turn the key switch to the “ON” position. 3. Raise the brush to the highest position (if necessary). 4. Raise the squeegee (if necessary). 5. Gently press the foot pedal and the machine will begin to move. 6. To stop, release pressure on the foot pedal. 7. To travel in reverse, select reverse with the forward/ reverse switch. 8. To stop, release pressure on the foot pedal. 9. When you stop the

READ THIS BOOK CAUTION: Read the Operator's Manual before using the appliance. This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your ALTO machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If operator(s) cannot read thi

54 Parts List ................................................................................................................................................................. 55 32” Boost Head Assembly Drawing ....................................................................................................................................... 56 Parts List ...........................................................................................................................................

Water “droplets” off when solution is off and they are flashing when solution is on. “Battery” blinks when Screens low voltage occurs. Arrows indicating vacuum status. AvailableThey are flashing when vac is on to Operator and off when vac is off. SCREEN 2 Example SCREEN 3 (Diagnostic) The Diagnostic only. It will not show unless a fault with the machine occurs. When the fault happens the icon and error code will be displayed. CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBT

The squeegee assembly has a break away feature that is also used for mounting the squeegee. Loosen the knobs on the squeegee (figure 8). Slide the stud into the slotted hole in the support frame on the machine. 2. Attach the vacuum hose cuff to the squeegee hose fitting (see figure 9). 3. Tighten knobs. NOTE: Do not overtighten or break away feature is lost and damage may occur. NOTE: To prevent damage to the squeegee or machine, the squeegee was designed to break away from the machine. If the s

CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Page -61 CLARKE TECHNOLOGY SCRUBTEC R 571, 586, 571 C, BOOST CLARKE TECHNOLOGY ® ®®®®® R RRRRR Electrical Panel Assembly Drawing and Parts List 3/08 Drawing # 11091A, 10782S, 10961S, 10989S 45 65 23 7 19 8 17 5 6 6 9 5 14 15 13 12 13 11 10 16 Ref Part No. Description Qty 1 2 3 4 980614 40932B 40965A 8548

The solution filter is dirty. A circuit breaker has tripped. Insufficient flow. Make sure the solution flow is set. Fill the solution tank. Clean the solution filter. Reset the circuit breaker. Increase flow with solution switch. The machine does not clean satisfactorily The brushes are worn. Need to use a different kind of brush/pad Check the brushes and replace if necessary. (the brushes have to be replaced when the bristles reach approximately .59 inches (15mm height.) Use a different kind of

X 1.06 O.D. 2 34 980614 Washer, 1/4” Starlock, Ext. 3 35 85700A Screw, 1/4-20 x 1 HHCS 1 36 413754 Grip, Solution Tank Clamp 1 CLARKE TECHNOLOGY Operator's Manual -SCRUBTEC R Manual Steering SCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual SteeringSCRUBTEC R Manual Steering Page -37 4 5 2A, 2B 8 567 9 11 12 12A,12B 13 14 17 18192627 28 29 4 5 2A, 2B 8 567 9 11 12 12A,12B 13 14 17 18192627 28 29 SCRUBTEC BOOST SCRUBTEC BOOSTSCRUBTEC BOOSTSCRUBTEC BOO

15 How to Operate the Machine .................................................................................................................................................. 16 How to Return One Touch to Factory Default Settings ......................................................................................... 16 How to Move Machine ............................................................................................................................................ 16 Seat Adjust