Always unplug and turn your Sport off before cleaning. Use a vacuum cleaner hose to clean the air intakes on the front grill. Always store your Work’n Play Sport in a dry place. 1) 2) 3) 4) 5) Comment l’utiliser Placer Work’n Play Sport a l’interieur dans un endroit sec. Poser vos bottes sur une surface plane. IMPORTANT! Avant d’allonger les tubes: Si le Work’n Play Sport a ete expose a des temperatures au dessous de 0 °C, laisser-le rechauffer avant l’utilisation. Metter l’appareil en marche po

Plug the power cord The appliance shall be supplied with220- 240V,50Hz, connected to a special receptacle more than 10A (reliably grounded). 2. Place the dehydrated clothes in your dryer Check the following items before putting clothes in. They shall be loaded in such a way that 2-3 pieces each time and not in a group to avoid tangling, which is not easy to turn it over resulting in uneven drying since the clothes were wrapped. Before drying your clothes Make sure if clothes have any special req

Donot use harsh or abrasive cleaners, this could damage the dryer. Clean the buildup such as lints on filters in time after each use, otherwise it will affect the performance of your dryer. Please unplug the power cord first when cleaning it. 1. Remove the filters Remove by pulling straight up with hands inserted into the four holes around the exhaust vent shroud in the sequence of Exhaust vent shroud - Lint filter - Exhaust filter , as shown in figure 1. ' ' 3. Install the filters After cleanin

Installation Instructions Gas & Electric Dryer Instructions d’installation Sécheuse à gaz ou électrique P/N 134940500A (0804) CONTENTS Pre-Installation Requirements..........................................................................................................................................2 Electrical Requirements..................................................................................................................................................3 Exhaust Syste

Mobile Home Installation Kit No. 346764 is available from your dealer. Refer to pages 2 and 3 for other important venting requirements. Installation MUST conform to current Manufactured Home Construction & Safety Standard (which is a Federal Regulation Title 24 CFR-Part 32-80) or when such standard is not applicable, with American National Standard for Mobile Homes. A CAUTION To prevent damage, do not use the control panel as a means to pick up or move the dryer. 2. Return the dryer to an up

The more the dryer is used, the more often you should check the exhaust system and vent hood for proper operation. ..NOTE Use of 90° quick-turn elbow required to meet minimum installation depth of free-standing dryer: • Straight back venting allows for 0” (0 cm) installation. • Venting right with 90° elbow allows for 0.75” (2 cm) installation. • Venting downward with 90° elbow allows for 0.75” (2 cm) installation. • Venting left with short, straight adapter and 90° elbow allows for 3.75” (9.5 cm

DO NOT install your dryer in a closet with a solid door. 4. Closet door ventilation required: A minimum of 120 square inches (774.2 cm.) of opening, equally divided at the top and bottom of the door, is required. Openings should be located 3 inches (7.6 cm) from bottom and top of door. Openings are required to be unobstructed when a door is installed. A louvered door with equivalent air openings for the full length of the door is acceptable. 60 sq. in. (387.1cm.) 3” (7.6cm) 60 sq. in. (387.1cm.)

2 Since your dryer is equipped with a power supply cord having an equipment-grounding conductor and a grounding plug, the plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances. If in doubt, call a licensed electrician. 3 DO NOT modify the plug provided with this appliance. If it will not fit the outlet, have a proper outlet installed by a qualifi ed electrician. Grounding requirements - Gas dryer (USA and Canada)

Refer to the pre-installation requirements in this manual for the proper power cord to be purchased. WARNING ELECTRICAL SHOCK HAZARD A U.L.-approved strain relief must be installed onto • power cord. If the strain relief is not attached, the cord can be pulled out of the dryer and can be cut by any movement of the cord, resulting in electrical shock. Do not use an aluminum wired receptacle with a• copper wired power cord and plug (or vice versa). A chemical reaction occurs between copper and alu

9-13 Pre-installation Requirements ................................................2 Reversing door .............................................................. 14-15 Installation Requirements ..................................................3-7 Accessories/Replacement parts ............................................16 Installed Dimensions .............................................................8 Francais ..............................................................................17