valutazioni - 3, GPA: 4.3 ( )

Produttore : Lincoln Electric File Size : 460.88 kb File Nome : Lingua di insegnamento:

With the 3.0 kVA, 115/230 VAC auxiliary power, one 115V duplex and one 230V grounding type receptacle are provided. The circuit is protected with circuit breakers. The rating of 3.0 kVA permits a maximum continuous current of 13 amps to be drawn from the 230 volt duplex receptacle. Or a total of 26 amps can be drawn from the 115 volt duplex receptacle. The 115 volt duplex receptacle has a configuration which permits 15 amps to be drawn from either half. The total combined load of all receptacles is not to exceed 3.0 kVA. An optional power plug kit is available. When this kit is specified, the customer is supplied with a plug for each receptacle. Carburetor Deicing Kit A carburetor deicing kit is installed on Classic lll welders leaving the factory. The purpose of the Carburetor Deicing Kit is to prevent carburetor icing when the outside temperature is 60°F/15.5°c or lower. See Carburetor Deicing Kit Usage Instructions For Seasonal Change Over on page B4. To obtain REPLACEMENT PARTS for the Carburetor Deicing Kit contact WIS-CON TOTAL POWER CORPORATION. Wis-Con Part# Description 10221023 10220028 10060025 X02355 #36 XM32067 XM37004 10250021 LIT10278 Complete Carburetor Deicing Kit Angled Heat Collector Shield 2”x18” Flexible Hose (Gates 28095) 1.56”-2.50” Gear Clamp M10X70 Bolt 3/8” Flat Washer Notice Decal Installation Instructions CARBURETOR DEICING KIT USAGE INSTRUCTIONS FOR SEASONAL CHANGE OVER WARNING ELECTRIC SHOCK can kill. • Do not operate with panels open. • Disconnect NEGATIVE(-) BATTERYLEAD before servicing. • Do not touch electrically live parts. MOVING PARTS can injure. • Keep guards in place. • Keep away from moving parts. • Only qualified personnel shouldinstall, use or service this equipment. The engine MUST BE COLD before seasonal change over of the carburetor deicing kit. When the AVERAGE AIR INTAKE TEMPERATURE (Average Ambient) is: Below 60°F / 15.5°C (Winter Season Configuration) 1. With the engine OFF, remove the negative cable from the battery. 2. Push the FLEXIBLE HOSE fully onto the HEAT COLLECTOR SHIELD outlet tube, see Figure 1. 3. Reconnect negative battery cable. FIGURE 1 E D C A B A. FUEL TANK B. HEAT COLLECTOR SHIELD C. FLEXIBLE HOSE D. GEAR CLAMP E. AIR FILTER Above 60°F / 15.5°C (Summer Season Configuration) 1. With the engine OFF, remove the negative cable from the battery. 2. Remove the FLEXIBLE HOSE from the HEAT COLLECTOR SHIELD outlet tube. 3. The FLEXIBLE HOSE is to be positioned per figure 2. CLASSIC III AND IIID B-4 B-4 OPERATION IMPORTANT: 1/2” clearance between the FLEXIBLE HOSE and the fuel tank edge is required. Also 2” clearance between FLEXIBLE HOSE and roof. 4. Reconnect negative battery cable. FIGURE 2 A B C A. FLEXIBLE HOSE B. HEAT COLLECTOR SHIELD C. AIR FILTER NOTE: On welders received directly from the factory, the “Deicing” kit is configured for “summer Seasons” CLASSIC III AND IIID C-1 C-1 ACCESSORIES OPTIONAL FEATURES (Field Installed) Accessory Set (K703) -Includes electrode and work cables, headshield, work clamp and electrode holder. Hi-Freq™ (K799) -Provides high frequency plus gas valve for DC TIG welding. Linc-Thaw™ (L2964-1) - Includes meter and fuses to protect welder when thawing frozen water pipes. WARNING Pipe Thawing IS NOT a CSA approved procedure. If not done properly, it can result in fire, explosion, damage to wiring which may make it unsafe, damage to pipes, burning up the welder, or other hazards. Do not use a welder to thaw pipe before reviewing Lincoln Bulletin E695.1 (dated October 1987 or later.) Power Plug Kit (K802C) -A power plug kit for the auxiliary power receptacles is available. (Provides a plug for each receptacle.) Remote Control Kit (K924-4) -Contains switch, receptacle, remote control rheostat, and 100 ft (30.5m) cable for adjusting the OCV at the welding site. Trailer (K768) -Two-wheeled trailer for in-plant and yard towing at speeds under 10 mph only. Trailer (K780) -Two-wheeled trailer with brakes, lights and fenders. (For highway use, consult applicable federal, state and local laws regarding possible additional requirements.) Trailer -Two-wheeled trailer with steel, torsion-bar axle, 54” (137cm) wheel track. Low sway, low centerof- gravity. Sturdy tread plate platform. Choice of 3 hitches. Add on fender & light package. For highway use, consult applicable federal, state, and local laws regarding possible additional requirements. Order: K913-1 Trailer, K913-2 Ball Hitch, K913-3 Lunette Eye Hitch, K913-4 Clevis Pin Hitch, K913-5 Fender & Light Kit. Wire Feed Module (K623-1) -Provides constant voltage (CV) output with improved arc stability for Innershield welding. Excellent for MIG welding. Recommended wire feeders are the LN-7, LN-23P and LN-25. (Factory installed on the K1428-3 and K1433-2). CLASSIC III AND IIID D-1 D-1 MAINTENANCE 4. When necessary, remove the sediment bowl, if so MAINTENANCE WARNING equipped, from beneath the fuel tank and clean out any accumulated dirt and water. Have qualified personnel do the ma...

Scarica la tua

Per scaricare, digitare 2 cifre :