valutazioni - 3, GPA: 4
(
)
)
|
Facilità d'uso
13 EARPHONE jack– Connects to earphones (not supplied) for personal listening. The size of jack is 1/8” monaural (3.5mm). 14 Cassette compartment 15 Number buttons– Press to select desired channels for viewing or recording. To select channels from 1 to 9, first press the 0 button and then 1 to 9. 26 27 +100 button– When selecting cable channels which are higher than 99, press this button first, then press the last two digits. (To select channel 125, first press the “+100” button then press “2” and “5”). 16 MENU button– Press to display the main menu on the TV screen. 17 DISPLAY button– Display the counter or the current channel number and current time on the TV screen. (See page 25.) 18 SPEED button– Press to choose the desired recording speed:SP/SLP. 19 T-PROG. CLEAR button– Press to cancel a setting of timer program. (See page 23.) COUNTER RESET button– Press to reset counter to 0:00:00. 20 GAME button– Sets the game mode and external input mode at the same time. (See page 14.) 21 TIME SEARCH button– Press to activate Time Search mode. 22 PAUSE/STILL button– Press to temporarily stop the tape during the recording or to view a still picture during playback. 23 MUTE button– Mutes the sound. Press it again to resume sound. 24 CHANNEL RETURN button– Press to go back to the previously viewed channel. For example, pressing this button once will change channel display from 3 (present channel) to 10 (previously viewed channel), and pressing it a second time will return from 10 to 3. 25 WAKE UP/SLEEP button– Sets the Wake up or Sleep Timer. (See page 23.) 26 Power cord– Connect to a standard AC outlet (120V/60Hz). 27 ANT. terminal– Connect to an antenna or cable system. - 8-EN 9I03 PREPARATION FOR USE ANTENNA/CABLE CONNECTIONS Cable Box (Not supplied) From Cable System VHF/UHF COMBINED ANTENNA The VHF/UHF Rod Antenna (supplied with 13” model only) is detachable. Insert the stem of the antenna into the hole on the upper-back portion of the TV/VCR.Connect the VHF/UHF Rod Antenna or VHF/UHF Combination Antenna to the ANT. terminal of the TV/VCR as shown in the diagram below.For the best reception, fully extend the VHF/UHF Rod Antenna and make the necessary adjustments. (Avoid touching the top section when adjusting.) NOTE: Before plugging the Rod antenna into antenna terminal, check that the pin is not bent. If it is bent, straighten the pin as illustrated, then plug the pin into antenna terminal. Bent pin Cable Plug (Needs to be straightened) (Straight pin) NOTE: The connection of an indoor antenna may not always give acceptable TV reception. VHF/UHF SEPARATE ANTENNAS In some areas it will be necessary to use an outdoor antenna. ANT. INOUT Rod Antenna (Supplied with 13” model only) VHF/UHF Antenna (Not supplied) VHF/UHF Combiner (Not supplied) Flat twin-lead cable UHF Antenna (Not supplied) VHF Antenna (Not supplied) 75-ohm Coaxial Cable (Not supplied) Satellite Box or From Cable System or Satellite Dish or or or or CABLE WITHOUT CONVERTER/ DESCRAMBLER BOX Use this connection if your cable system connects directly to your TV/VCR without a converter box. By using this connection you can: 1) Use the TV/VCR remote to select channels. 2) Program one or more unscrambled channels for Automatic Timer Recording. NOTE: This unit will ONLY record and view the same channel. CABLE WITH CONVERTER/ DESCRAMBLER BOX OR SATELLITE BOX If your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown here. By using this connection you can also record scrambled channels. However, channel selection must be made with the converter box or satellite box. This means that channels cannot be changed using the TV/VCR Remote Control. Unattended timer recording is limited to one channel at a time. Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical. - 9-EN 9I03 TO RECORD A SCRAMBLED/UNSCRAMBLED CHANNEL 1. Set the TV/VCR channel selector to the output channel of the Cable Converter Box or Satellite Box. (Ex. CH3) 2.Select the channel to record from your Cable Converter Box or Satellite Box. EXTERNAL INPUT MODE When using an external input signal (another VCR or video camera), connect the player’s audio/video output cables to the AUDIO IN/ VIDEO IN jacks of your TV/VCR. Then press the CHANNEL K or L button until “AUX” appears on the screen. NOTE: “AUX” is found below the lowest memorized channel. AUX (Example: CH2) INSTALLING THE BATTERIES 1)Open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow. 2)Insert 2 “AA” penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings. 3)Replace the cover. SET UP FOR USE Y...