valutazioni - 4, GPA: 4.3
(
)
)
|
Facilità d'uso
The output of the green tube is stationary. The outputs of the red and blue tubes can be adjusted. When properly aligned, the outputs of all three tubes should be directly over each other to produce the white lines. Press MENU, 2, ENTER, 3, ENTER to display the CONVERGENCE ADJUSTMENT. Press the CURSOR , to move the color displayed up or down. Press the CURSOR , to move the color displayed left or right. Press ENTER to change the color. Press MENU to exit. -SOUND- FUNCTIONS Press MENU, 3, ENTER to display the -SOUND- functions. SOUND PROGRAM is for your preferred settings - balance, bass and treble. SOUND SETTING is used to improve the sound quality. . SOUND PROGRAM You can have two sets of preferred settings, PREFERENCE-A, PREFERENCE-B or use the factory PRESET settings. Press MENU, 3, ENTER, 1, ENTER to select the SOUND PROGRAM. Press the CURSOR buttons to select and make adjustments. BALANCE - This function will control the left, right balance of the TV internal speakers, the AUDIO TO HI-FI output, and the surround speakers. BASS - This function controls the low frequency audio to all speakers. TREBLE - This function controls the high frequency to all speakers. . SOUND SETTING Use the sound settings to improve the sound performance of your TV depending on listening conditions. Press MENU, 3, ENTER, 2, ENTER to display the SOUND SETTING. Use the CURSOR , to select a function. Press ENTER to set a function or to turn it on or off. . MTS MODE (Multi-Channel Television Sound) will allow you to select STEREO (a stereo broadcast), SA (second audio) program which may be a secondary language, weather report, etc. or MONO (monaural sound) used when receiving a weak stereo broadcast. The sources received will be displayed below the channel number. The source you select will be displayed to the left of the channel number. See example below for each selection when both stereo and second audio are received (monaural is always received). . DYNAMIC BASS This function allows you to enjoy spectacular bass sound that would normally be heard only with expensive home speaker systems. . LOUDNESS This function will improve the quality of both low and high frequency sounds when listening at low volume levels. . INT. SPEAKERS This function is useful when first setting up the external speakers, or if you prefer to use only speakers from a separate stereo system. CARE OF YOUR PROJECTION TV AND REMOTE CONTROLS DO . Dust the screen and cabinet with a soft cloth. . Clean the screen with a soft cloth moistened in warm water. Dry with a soft cloth. (A mild soap may be used if the screen is extremely dirty.) . Place your TV and remote controls away from extreme heat, humidity and extremely dusty places. . Remove the plug from the wall outlet if your television set will not be used for a long period of time, for instance, when you go on vacation. DO NOT . Do not clean your screen or cabinet with strong cleaners, polishes or chemically treated cloth. . Do not place rubber or vinyl products or cellophane tape on your set. . Do not touch the screen too often. . Do not subject the Remote Control to shocks such as dropping it on the floor, etc. Physical damage to the precision parts may result. . Avoid placing the Remote Control in a high humidity place or getting it wet. Don’t leave it on or near a heater. Excessive heat or moisture may cause the unit to cease operation. . When the batteries run down, remote control operation will become erratic or possibly stop altogether. Replace the old batteries with two fresh "AA" size batteries for either the Genius remote or the Easy remote. . Exposure of the viewing screen to prolonged direct sunlight or heat may cause the screen to permanently warp, resulting in a distorted picture. TROUBLESHOOTING RECEPTION PROBLEMS (EXTERNAL TO THE TV) . IGNITION NOISE: Black spots or horizontal streaks may appear, picture may flutter or drift. Usually caused by interference from automobile ignition systems, neon lamps, electrical drills and other electrical appliances. . GHOSTS: . GHOSTS: Ghosts are caused by the television signal following two paths. One is the direct path and the other is reflected from tall buildings, hills or some other objects. Changing the direction or position of the antenna may improve reception. Ghosting may also be caused by defects in the antenna system such as unshielded leads or connecting several sets to the same antenna without using multiple antenna couplers. . SNOW: If your receiver is located in the fringe area of a television station where the signal is weak, your picture may be marred by the appearance of small dots. When the signal is extremely weak, it may be necessary to install a special antenna to improve the picture. . RADIO FREQUENCY INTERFERENCE: The interference produces moving ripples or diagonal streaks, and in some cases, causes loss of contrast in the picture. BEFORE CALLING FOR SERVICE This Projection Television incorporates advanced power surge protection techno...
Questo manuale è adatto anche per i modelli :TV - 46EX3B (859.22 kb)
TV - 50ES1B (859.22 kb)
TV - 50ES1K (859.22 kb)
TV - 46EX4K (859.22 kb)