valutazioni - 4, GPA: 4.5
(
)
)
|
Facilità d'uso
(However, the image will not be displayed properly if the signals exceed 1,200 lines.) (2) The display resolution is a maximum of 640 . 480 dots when the aspect mode is set to “4:3”, and 852 . 480 dots when the aspect mode is set to “16:9”. If the display resolution exceeds these maximums, it may not be possible to show fine detail with sufficient clarity. (3) Some PC models cannot be connected to the set. (4) There is no need to use an adapter for computers with DOS/V compatible D-sub 15P terminal. (5) The computer shown in the illustration is for example purposes only. (6) Additional equipment and cables shown are not supplied with this set. (7) Do not set the horizontal and vertical scanning frequencies for PC signals which are above or below the specified frequency range. Signal Names for D-sub 15P Connector 1 678 3 9 45 10 1514131211 2 Pin No. Signal Name Pin No. Signal Name Pin No. Signal Name 1 R 6 GND (Ground) 11 NC (not connected) 2 G 7 GND (Ground) 12 NC 3 B 8 GND (Ground) 13 HD/SYNC 4 NC (not connected) 9 NC (not connected) 14 VD 5 GND (Ground) 10 GND (Ground) 15 NC Pin Layout for PC Input Terminal Power ON / OFF 1 Connect the AC cord plug to the Plasma TV. • Fix the power cord plug securely with the clamper (see page 11). Remote control senser POWER POWER button 2 Power indicater Power on: Red Power off: No Light TV VCR DVD DBS RCVR CBL LIGHT TV/VIDEO A -ANTENNA - B SAP AUX POWER Note: The TV will still consume some power as long as the power cord is inserted into the wall outlet. 3 Connect the plug to the wall outlet. Press to turn the TV on or off. Location of Controls The Main Unit Remote control sensor OK Choose menu and submenu entry. S-VIDEO PC CHANNELVOLUMEMENU OK HPJ VIDEO VIDEO3 L AUDIO R SD CARD PUSH-EJECT POWER S VIDEO PC CHANNELVOLUMEOKMENU TV/VIDEO HPJ VIDEO INPUT3 L AUDIO R SD CARD PUSH-EJECT POWER button Volume adjusters C.A.T.S. sensor Plasma C.A.T.S. (Contrast Automatic Tracking System) automatically senses the ambient light conditions and adjusts the brightness and gradation accordingly, to optimise contrast. Effective when Pic Mode is set to Auto (see page 26). SD CARD slot MENU Display Main Menu or return one step backward in menus (see pages 24, 57). Channel selectors TV/VIDEO Change the input mode. Location of Controls TV POWER MENU R-TUNE PIP MIN REW PIP MAX FFPLAY PROG EXIT VCR DVD DBS RCVR CBL LIGHT TV/VIDEO A -ANTENNA - B SAP 1 2 3 4 5 6 7 8 0 9 AUX ASPECT MUTE RECALL BBE STOP PAUSE FREEZE TV/VCR PIP SPLIT MOVE SWAP SEARCH OPEN/CLOSE PIP CH DVD/VCR CH REC CH VOL CH VOLOK The Illuminated Remote Control COMPONENT 2 HDMITV COMPONENT 1 VIDEO 3PC VIDEO 1VIDEO 2 POWER Turn the TV ON or OFF. TV/VIDEO Change the input mode. SD Access Photo Viewer (see page 48). R-TUNE Switch to previously viewed channel and input modes. Mode Selection buttons (see page 59) TV: TV VCR: VCR DVD: DVD DBS: Digital Broadcasting Satellite RCVR:Receiver/Amplifier CBL: Cable TV AUX: Aux PIP MIN REW PIP MAX FFPLAY STOP PAUSE FREEZE TV/VCR SEARCH OPEN/CLOSE PIP CH DVD/VCR CH REC PIP MIN, PIP MAX Change the size of PIP frame (see page 52). Operation of other Device (see pages 63, 64) SEARCH Display search frames during PIP or SPLIT operation (see pages 53, 55). PIP CH Select the channel during PIP or SPLIT operation (see pages 52, 54). FREEZE Freeze the picture (see pages 53, 55). PIP PIP (Picture in Picture) Operation (see page 52) SPLIT Split Screen (see page 54) MOVE Move PIP frame (see page 53). SWAP Swap pictures in PIP or SPLIT operation (see pages 52, 54). Location of Controls EXIT Exit menus. CH VOL CH VOLOK MENU EXIT CH: Change to the next channel up. : Move cursor upward during menu mode. VOL : Reduces volume. : Move cursor to the left during menu mode. Choose menu and submenu entry. VOL : Increase volume. : Move cursor to the right during menu mode. CH: Change to the next channel down. : Move cursor downward during menu mode. A: 15-1 KPBS - HD Add FAV TV-G 1080i VIVID HDMI 12:30 pm 30CC SAP Antenna designation, Channel and program # and Station identifier Rating ClockProgram Aspect Picture mode setting PIP/SPLIT CH number or Input information Closed Caption SAP indication Time remaining in Sleep Timer Press OK button to add or delete the channel in the Favorite channel list (see page 30). BBE Turn BBE VIVA 3D OFF or ON (see page 29). RECALL Display or remove the channel banner. ASPECT Change the screen aspect (see page 56). MUTE Mute the sound. Press again to cancel the mute. MENU Display Main Menu or return one step backward in menus (see pages 24, 57). Direct program number selection buttons PROG -: When tuning digital channel, press the button to enter the minor number in a compound channel number. • To enter the channel number ex. CH 15-1: [1] [5] [-] [1] [OK] SAP • Digital channel Select the audio track (if available). Audio Track 1 of 1 (English) • Analog channel Cycle through different audio modes. ex. If receiving Stereo, SAP and Mono or receiving Stereo and Mono only: Stereo SAP Mono L...
Questo manuale è adatto anche per i modelli :TV - TH-37PD25 (1.86 mb)