valutazioni - 2, GPA: 3.5
(
)
)
|
Facilità d'uso
With the operation of the interface confirmed, you may continue with the installation. If you experience difficulties in operation, please see our troubleshooting chart in section 3.2. 5. Decide on a convenient location to mount your Mobile Device. 6. Run the black docking cable from the interface to the desired mounting location. Use caution to not cut, pinch, or crimp the cable during this step. Avoid moving parts, vehicle wiring harnesses and areas of excessive heat when routing the cable. 7. Secure the interface in the dash cavity behind the radio using; double sided tape, Velcro or wire ties. Make sure to check for proper clearance and avoid moving parts. Take into account the size of the interface and the wire harness and do not force the interface and harness into a space that is too tight, damage to the harness may result. 8. Now that the interface is secured and the docking cable has been run, you may reinstall the radio and replace any panels that may have been removed to access the radio. You are ready to enjoy your Mobile Device in your vehicle! 13 Chapter 3- Operation 3.1 Operation SELECTING THE AUDIO DEVICE To select the mobile device from the radio, press the button that would normally activate the factory CD changer. This button varies by vehicle manufacturers. In some applications (using config.#8) the Audio2car is accessed like an XM reciever, In these cases you will press the appropriate activation button. Some radio models require pressing the “Seek >” button once, after pressing the CD button. Yet, it may also be necessary to press Play on the mobile device itself to begin playback. In some cases, if it is the first time selecting the mobile device from the radio it may take up to three minutes for the Audio2car to initialize. RADIO DISPLAY DURING Mobile device OPERTION Some factory radio’s may show DISC and TRACK numbers on the display of the radio. The Audio2car interface does not send any information from the mobile device to the radio. This means that the DISC and TRACK numbers shown on the display will not and can not reflect the song number on the mobile device due to the complex nature of the music library. Some factory radio’s may flash zero’s on the display of the radio, or toggle back and forth between Tracks “1” and “2”. All these are normal behaviors and do not represent a malfunction. 14 3.2 Trouble Shooting Symptom Cause Remedy No Power Blown fuse in vehicle fuse block. Replace fuse with same amp rating. If the fuse blows again, call tech support. No Power Bad connection Check cable and wiring connection. Alternator noise is heard (Changes with Engine RPM) Improper wiring creates a ground loop Install a Ground loop isolator or seek professional service from a local car audio shop. Radio is not recognizing Audio2car interface Bad cables or cables are not connected properly between converter box and car radio Check connection and cables, push in firmly. Radio is not recognizing Audio2car interface Wrong configuration on the interface Select the right pconfiguration for your car. (See section 1.5) Radio is not recognizing Audio2car interface Yellow and black wires are not connected to Constant 12V+ and Ground. (When applicable) Please read wiring instructions in chapter 2 of this manual and see if your car requires to connect the yellow and black cable to power and ground Mobile device Audio is Low or Distorted Audio2car interface is connected with an external CD changer or other external factory audio source Disconnect the factory external audio source. Mobile device is not charging Yellow and black wires are not connected to Constant 12V+ and Ground. (When applicable) Please read your vehicles section in this manual and see if your car requires to connect the yellow and black cable to power and ground For consumer technical support call: 866-788-4237 in the US or 727-572-9255 ext.262 for international calls Hours: 9:30 am-6:00 pm E.S.T. MON - FRI 15 3.3 Warranty One Year Limited Warranty The quality controls used in the manufacture of this product will ensure your satisfaction. This warranty applies only to the original purchaser of this product from an authorized Peripheral Elecronics dealer. This warranty covers any supplied or manufactured parts of this product that, upon inspection by Peripheral Electronics authorized personnel, is found to have failed in normal use due to defects in material or workmanship. This warranty does not apply to installation expenses. Attempting to service or modify this unit, operating this unit under conditions other than the recommended voltage will render this WARRANTY VOID. Unless otherwise prescribed by law, Peripheral Electronics shall not be liable for any personal injury, property damage and or any incidental or consequential damages of any kind (including water damage) resulting from malfunctions, defects, misuse, improper installation or alteration of this product. All parts of this Peripheral Electronics product are guaranteed for...
Questo manuale è adatto anche per i modelli :TV - PXDX-KI (2.06 mb)