In the screen, n/a indicates that the remote sensor is not attached. To change the temperature calibration, press Up or Down to select the internal or remote sensor. Once selected, press Plus (+) or Minus (-) to change the temperature calibration to the desired setting. Press Refresh (right blank button) to update the information on this screen. Note: When you change a temperature calibration and exit this screen, it may take a few seconds for the new temperature to be displayed on the Thermosta

customer's e-mail us at: faucetsupport@amstd.com For Parts, Service, Warranty or other Assistance, please call 1-800-442-1902 (In Canada: 1-800-387-0369) NOTE TO INSTALLER: Please give this manual to the customer after installation. (In Toronto Area only: 1-905-3061093) Specifications Installation Adjust Temperature Service Replacement Parts 1 2 3 3 4 Installation InstructionsInstallation InstructionsSELECTRONIC™ Thermostatic Mixing Valve Certified to comply with ASME A112.18.1M © 2005 American

¦ Press again to change to your desired Set 3COOL TEMP Temperature. Hold the key for 2 seconds to or fast-advance the Set Temperature. ¦ Press to return to normal mode, or wait 5 seconds for it to return automatically. /return ¦ The current program number will flash to SA signify the Temporary Override. ¦ At the next program change time, the Tem-PM porary Override is cancelled, and the next program temperature becomes the setpoint COOL TEMP 3 temperature. To end the Temporary Manual Override: ho

• The Balance Setpoint Limits can be adjusted according to the manufacturer’s specifications under “Balance Setpoint” – See Installation Settings. 3) When the RC-1000 makes a call for auxiliary heat, the heat pump compressor is turned off and the auxiliary heat is used exclusively. Heat Pump (2 Stage Heat / 1 Stage Cool) 9 876543 1 24VAC Common 24VAC "HOT" Auxilirary Heat Compressor Ground Fault Fan Compressor Relay Aux Heat Relay Fan Relay Fault Relay Reversing ValveEnergized in Cool Energized

Set the switch to HG for a gas furnace or oil burner. Set the switch to HE for electric furnaces. (The switch has no effect when the system is set to cooling mode.) 5. Insert two fresh AA alkaline batteries. 6. Align the thermostat with the the wall plate, and snap the two halves together. 7. Restore power at the electrical panel or furnace. Thermometer System Switch Set Temperature Slider Fan Switch Battery Indicator Operation 1. Set the Set Temperature slider to the desired temperature. 2. The

FEATURES B Full seven-day program capability; different schedules and temperature setpoints may be selected for everyday to match the homeowner’s flexible schedule. B Copy key makes programming easier and faster for the installer and homeowner. B Daylight Savings Time (DST) key for quick change in and out of Daylight Savings Time. B Models available with programmable fan operation for added homeowner comfort. B Easy temporary temperature setpoint changes for current period, vacation hold (1 to 2

4. Using the provided stickers, label each wire according to the chart. RC Y G W W (If the terminals are not labeled, contact a qualified HVAC technician.) note: Wire colors do not always comply with standards, so wire color should be ignored. refer to the existing terminal designation for proper identification. *If wires marked Y & C are both present, C may be a Common wire and should not be used. If you have a wire marked C, do not connect it to any terminal. This wire is used only for non-bat

Minimum capillary tube bending diameter is 1/2” I.D. (see Figure 4). Figure 3 (Sensing Bulb) 1” Do Not Bend or Kink Crimped End 1/2” Rod Figure 4 (Capillary Tube) C. Any deformations of bulb or capillary that result in leakage of fluid from control renders control inoperative. D. Avoid passing control capillary tube through zones whose temperature is in excess of controlled process temperature. Erratic control or destruction of control function may result. WIRING ELECTRIC SHOCK HAZARD. Disconect

A 1/4 inch NPT vent is provided on the pressure regulator body for this purpose. The vent location is shown in Figure 2-3. When air is used as the pressure source, the vent fitting may be allowed to bleed into the atmosphere. If fuel gas or other hazardous type gases are used as the pressure source for a Remote Set Regulator, the VENT port must be piped to a safe location. ** Warning ** Covers of Remote Set Regulators operating in hazardous areas should not be removed. If servicing is required,

The display will be blank when no battery power is left. The system will remain off until new batteries are installed. (Your programs and time settings will be lost if the batteries are not replaced within one minute.) The thermostat will resume normal operation after new batteries are installed. 50 hold/return hold/return icons and features, cont. 7. Auto recovery – allows heating and cooling systems to gradually recover from an energy-saving setpoint temperature to a comfort setpoint temperatu