valutazioni - 5, GPA: 4.8
(
)
)
|
Facilità d'uso
However, with “Precise print mode” selected, feed accuracy will increase because the media is fed while the sensor threshold value is being monitored all the time. Print Head Sensor Feed direction After a page alignment is initiated, the first print start position is detected. The media is fed until this position is aligned with the Print Head position. After page alignment Before page alignment Page alignment in Strict feed mode If the tear-off is to be performed, the media will be further fed up to a tear-off position from the page alignment position. Print Head SensorTear-off position Feed direction After page alignment After tear-off Tear-off after page alignment In addition, whenever “Precise print mode” is selected, a page alignment is performed in order to increase the print accuracy after the printer is started up. 7- 6 7. PRINTER OPERATION ¦ Page alignment when “Paper saving mode” is selected In the page alignment when “Paper saving mode” is selected, first, the loaded media is fed to find the first print start position that passes the sensor. Next, it is fed until the next print start position lying behind the print head is aligned to the Print Head position. Compared to the “Precise print mode”, the amount of media ejected is smaller, eventually waste of paper is saved. With “Paper saving mode” selected, the media is fed based on the media settings sent from the printer driver. Therefore, the feed accuracy decreases compared to the “Precise print mode”. Feed direction Print Head Sensor After a page alignment is initiated, the first print start position is detected. The media is fed until this position is aligned with the Print Head position. The media is fed until the print start position right behind the Print Head is aligned to the Print Head Position. Page alignment After page alignment Page alignment in Strict feed mode If the tear-off is to be performed, the media will be further fed up to a tear-off position from the page alignment position. Tear-off position Print Head Sensor Feed direction After page alignment After tear-off Tear-off after page alignment Unlike “Precise print mode”, a page alignment is not performed after the printer is started up. 7- 7 7. PRINTER OPERATION ¦ Page alignment when Fixed Length feed mode is selected If Fixed Length feed mode is selected, the page alignment will be performed as described below: . If the tear-off is not enabled, a page alignment will not be performed. . If the tear-off is enabled, the media will be fed up to a tear-off position. *If both tear-off and cut operations are enabled, the media is fed past a cut position from the Print Head Position, then cut. Please refer to Section 1.4.1 Cut position for further information regarding a cut position. 7.4 Media Calibration “Media calibration” is a function to measure a sensor threshold value used to detect the upper and lower edges of a gap, notch, or black mark of the loaded media (hereafter referred to as “UP” and “Lo”, respectively), the media length excluding a gap, notch, or black mark (hereafter referred to as Lc), and the media length including them (hereafter referred to as “FL”). Feed direction Lc, FL, Lo and UP of die-cut label (in Strict feed mode) Perform a media calibration when using the printer for the first time or new media that has never been used in Strict feed mode. (A media feed error may occur when the size of the loaded media and the result of the media calibration do not match.) The printer advances the media based on the result of the media calibration. This is not mandatory for the Easy feed mode, but if a media feed error occurs, perform a media calibration. * A media calibration is not mandatory the Easy feed mode, but if a media feed error occurs, perform a media calibration. Note that when the printer is placed in Fixed Length feed mode, a media calibration is not required. 7- 8 7. PRINTER OPERATION ¦ How to perform a media calibration Use the following steps to perform a media calibration from the printer driver. Precautions . Before performing a print test, please refer to the Printer Driver Setup Guide, and install the printer driver. In addition, the information of the media in use for a print test must be register in the printer driver and selected in advance. Please refer to the Help for the Printer Driver for further information. 1. Load a ribbon and media in place for a print test. Turn the Power Switch on. Refer to sections 4. LOADING THE RIBBON and 5. LOADING THE MEDIA. Precautions . Do not load a ribbon when thermal paper is used. 2. Open the printers folder. . For Windows XP, open the [Printers and Faxes] folder from the [Start] menu. If [Printers and Faxes] cannot be found, open the folder from the Control Panel. . For Windows 2000, click the [Start] button. Move the cursor to [Settings] and select [Printers]. 3. Right-click on an icon of the currently selected printer. Choose and click on the [Properties]. The “printer properties” dialog box appears. 7- 9 7...
Questo manuale è adatto anche per i modelli :Allestimento di negozi - B-SX600 SERIES (3.09 mb)