Consult Table 4-2 for more information regarding keyboard wedge interface types. The correct interface cable is included for the imager interface type you ordered. NOTE QuickScan® QS6500/QS6500 BT Table 4-2. Keyboard Wedge Interface Reference I/F Type PCs Supported A PC/XT w/Alternate Key Encoding B AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80, 90 & 95 w/Alternate Key Encoding C PS/2 25 and 30 w/Alternate Key Encoding D PC/XT w/Standard Key Encoding E AT, PS/2 25-286, 30-286, 50, 50Z, 60, 70, 80

This Software is being provided to you under license, subject to the terms and conditions of this Agreement. If you use the Datalogic Product, you will be deemed to have accepted the terms and conditions of this Agreement. If you do not intend to be bound to the terms of this Agreement, Datalogic is not willing to license the Software to you, you may not use the Datalogic Product or the Software, and you must contact the party from whom you acquired the Datalogic Product for instructions. 1. Def

3. Scan the hex digit bar codes for 4, 1 and 4, 2 on the inside back cover of this manual. 22 QS2500 4. Scan the Store Settings bar code on the inside back cover. 5. Repeat the same procedure for the G2 characters. 6. Scan the Exit bar code. 7. Insert the data group 1–4 position. (page 24.) Start Program $ Option Bar Code Option Alphanumeric Entry Prefix None 00* 1–22 characters 00–ffhex ASCII code None 00 Suffix 1–22 characters 00–ffhex ASCII code * Preamble None 00* 1–22 characters 00–ffhe

(119 g) Color Black or White Electrical Characteristics Voltage & Current QD2110 4-14 VDC QD2130 5.0 VDC +/-10% 180mA @ 5V Typical Idle 345mA @ 5V Typical Scanning Performance Characteristics Light Source 617nm LEDs Roll (Tilt) Tolerance ± 45° from normal Pitch Tolerance ± 65° Skew (Yaw) Tolerance ± 65° Scan Angle 43° ± 3° Depth of Field 4.0 mil 3.0 - 9.5 cm 5.0 mil 2.3 - 14 cm 7.5 mil 1.5 - 26.5 cm 10 mil (80% UPC) 1.3 - 37.5 cm 13 mil (100% UPC) 2.5 - 46.5 cm 15 mil to 48 cm 20 mil to 59 cm Mi

Page references are also provided for feature descriptions and programming bar codes for each parameter. A column has also been provided for recording of your preferred default settings for these same configurable features. Table 30. Standard Defaults Parameter Default Your Setting Page Number General Features Set Default Parameter Restore Defaults 21 Beeper Tone Medium 22 Beeper Volume High 22 Power Mode Continuous On 23 Scan Line Width Full Width 25 Laser On Time 3.0 Sec 25 Beep After Good Rea

192 I 2 of 5 Check Character Calculation ................................................................................ 193 I 2 of 5 Check Character Transmission ............................................................................. 194 I 2 of 5 Minimum Reads ................................................................................................. 195 2 of 5 Decoding Level .................................................................................................... 196 I

During this process a series of brief “ticks” indicates that reading is proceeding correctly. ADVANCED FORMATTING NOT FOR PEN INTERFACES • CONCATENATION • • ADVANCEDFORMATTING • Please follow the setup procedure carefully for these parameters. NOTE The Advanced Formatting parameters may not be compatible with the IBM USB POS interface selection. NOTE 1. Read the Enter Configuration code ONCE, available at the top of page. 2. Read configuration codes precisely following the numbered procedure giv

EAN 8 IAAG1oI .. EAN 13 IAAH1rI .. UPC A IAAI1uI .. UPC E IAAJ1xI NO CHECK DIGIT TRANSMISSION EAN 8 IAAG0kI EAN 13 IAAH0nI UPC A IAAI0qI UPC E IAAJ0tI Enter Configuration Exit and Save Configuration I$+;I CODE SELECTION I$-?I CONVERSION OPTIONS UPC E to UPC A conversion IAAAAI UPC A to EAN 13 conversion IAACEI Enable only ISBN conversion IAP1nI Enable both ISBN and ISSN conversion IAP3tI UPC E to EAN 13 conversion IAABCI EAN 8 to EAN 13 conversion IAAD"I Enable only ISSN conversion IAP2qI Disabl

SERVICE, SUPPORT AND WARRANTY Datalogic provides several services as well as technical support through its website. Log on to and click on the links indicated for further information including: · Datalogic Services - Warranty Extensions and Maintenance Agreements · Downloads - Software Downloads, Manuals and Catalogues · Contact Us - Listing of Datalogic Subsidiaries and Quality Partners · Authorised Repair Centres SAFETY PRECAUTIONS For installation, use and maintenance it is not necessary to o

GENERIC IMMUNITY STANDARD. PART 2: INDUSTRIAL ENVIRONMENT Following the provision of the Directive(s): 89/336 CEE AND SUCCESSIVE AMENDMENTS, 92/31 CEE; 93/68 CEE Ruggero Cacioppo Lippo di Calderara, 16.11.1998 Quality Assurance Supervisor Product names mentioned herein are for identification purposes only and may be trademarks and or registered trademarks of their respective companies. Datalogic S.p.A. reserves the right to make modifications and improvements without prior notification. . - 1999