valutazioni - 3, GPA: 4.7
(
)
)
|
Facilità d'uso
The track will then disappear and the indicators will again begin to appear in succession. 13 The upper left corner of the display will show the approximate number of calories you have burned during your workout. The lower left corner of the display will show the elapsed time and the distance that you have walked or run during your workout. The lower left corner of the display will also show the incline level of the treadmill for a few seconds each time the incline setting changes. Note: When a personal trainer program is selected, the lower left corner of the display will show the time remaining in the program instead of the elapsed time. The lower right corner of the display will show the speed of the walking belt. When you use the handgrip pulse sensor, the lower right corner of the display will also show your heart rate. To reset the display, press the Stop button, remove the key, and then reinsert the key. 6. Measure your heart rate if desired. Before using the handgrip pulse sensor, remove the sheets of clear plastic from the metal contacts on the handgrip pulse sensor. In addition, make sure that your hands are clean. To measure your heart rate, stand on the foot rails and hold the metal contacts on the Contacts handrail— avoid moving your hands. When your pulse is detected, the heart symbol in the display will flash each time your heart beats, one or two dashes will appear, and then your heart rate will be shown. For the most accurate heart rate reading, continue to hold the contacts for about 15 seconds. 7. Turn on the fan if desired. The fan features low and high speed settings. Press the fan button repeatedly to select a fan speed or to turn off the fan. Note: If the fan is on when the walking belt is stopped, the fan will turn off automatically after a few minutes. 8. When you are finished exercising, remove the key from the console. Step onto the foot rails, press the Stop button, and adjust the incline of the treadmill to the lowest setting. The incline must be at the lowest setting when you fold the treadmill to the storage position, or you may damage the treadmill. Next, remove the key from the console and put it in a secure place. When you are finished using the treadmill, switch the reset/off circuit breaker to the “off” position and unplug the power cord. IMPORTANT: If you do not do this, the treadmill’s electrical components may wear prematurely. 14 HOW TO USE A PERSONAL TRAINER PROGRAM 1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 13. 2. Select a personal trainer program. To select a Certified Personal Trainer Program, press the Program Select button repeatedly until “P– 1,” “P– 2,” “P– 3,” or “P– 4” appears in the display. When a personal trainer program is selected, the maximum incline setting of the program and the maximum speed setting of the program will flash in the display for a few seconds. The display will then show how long the program will last. A profile of the speed settings of the program will scroll across the matrix in the upper right corner of the display. 3. Press the Start button to start the program. A moment after the button is pressed, the treadmill will automatically adjust to the first speed and incline settings of the program. Hold the handrails and begin walking. Each program is divided into 30 one-minute segments. One speed setting and one incline setting are programmed for each segment. Note: The same speed setting and/or incline setting may be programmed for two or more consecutive segments. During the program, the profile will show your progress. The flashing segment of the profile represents the current segment of the program. The height of the flashing segment indicates the speed setting for the current segment. At the end of each segment, a series of tones will sound Current Segment and the next segment of the profile will begin to flash. If a different speed and/or incline setting is programmed for the next segment, the speed or incline setting will flash in the display to alert you. The program will continue in this way until the last segment of the profile flashes in the display and the last segment ends. The walking belt will then slow to a stop. If the speed or incline setting for the current segment is too high or too low, you can manually override the setting by pressing the Speed or Incline buttons. Important: When the current segment of the program ends, the treadmill will automatically adjust to the speed and incline settings for the next segment. To stop the program at any time, press the Stop button. The time will begin to flash in the display. To restart the program, press the Start button. The walking belt will begin to move at 1 mph. When the next segment of the program begins, the treadmill will automatically adjust to the speed and incline settings for the next segment. 4. Follow your progress with the display. See step 5 on pages 13 and 14. 5. Measure your heart rate if desired. See step 6 on page 14. 6. Turn ...