valutazioni - 4, GPA: 4.3 ( )

Produttore : Star Trac File Size : 2.62 mb File Nome : Lingua di insegnamento:

• 60w power supply (NOT INCLUDED IN THE E-TRi KIT) • Power cord, AS/NZS 3112 (NOT INCLUDED IN THE E-TRi KIT) • Power cord, Nema 6-15 (NOT INCLUDED IN THE E-TRi KIT) • Power cord, Nema 5-15 (NOT INCLUDED IN THE E-TRi KIT) • Owners manual • Warranty card. 620-7991 Rev 002 PAL/SECAM Kit (Europe, Middle East) • PVS assembly with mounting bracket, cables, and display cap with grommet (There are 5 cables in the neck) • Center console keypad assembly • Entertainment headphone jack and mount • Hardware tool kit, including: • (1) Headphone icon • (4) M8 x 20mm buttonhead screws • (5) M4 x 0.7X19L screws • (1) M8 hex nut • (2) 5” tie straps • Silicon wrap • F-type male to female PAL/SECAM coaxial adapter • 5MM hex Allen key. • 60w power supply (NOT INCLUDED IN THE E-TRi KIT) • Power cord, CEE 7/7 (NOT INCLUDED IN THE E-TRi KIT) • Power cord, Nema 6-15 (NOT INCLUDED IN THE E-TRi KIT) • Power cord, BS 1363 (NOT INCLUDED IN THE E-TRi KIT) • Owners manual • Warranty card. Required Tool for Installation • 5MM hex Allen key • #2 Phillips screwdriver (Not Included) • 1/2” wrench (for E-TRi kits only, not included) • Wire cutters (Not Included) • Pliers (Not Included) • Step stool (Not Included) 620-7991 Rev 002 INSTALLING YOUR PVS ON THE E-UB, E-RB, E-TBT, AND E-ST INSTALLING YOUR PVS ON THE E-UB, E-RB, E-TBT, AND E-ST The Star Trac Personal Viewing Screen is different for each of your Star Trac E-Series Cardio products. Make sure you have the proper kit for the E-Series product you are installing. The E-UBi, E- RBi, E-TBTi, and the E-STi will follow the same basic steps for installation. For the E-TRi turn to appropriate section of this manual. STEP 1. Using a #2 Phillips screwdriver, remove the (8) screws on the back of the display plastic. Set the screws aside, you will need them for reassembly. STEP 2. After the screws have been removed, carefully open the display plastic, so as to not detach the inner cables from the display. Disconnect the ground wire 1 between the heart rate board and the display mount. STEP 3. Disconnect the 12-pin serial cable 2 and the heart rate cable 3 from the display. After all the cable/harnessing has been disconnected, place the front display plastics aside for later use. Be careful with the display and place it face down on top of a non-scratching surface. 620-7991 Rev 002 You can use the foam bag that ships inside the Personal Viewing Screen package to place the display face onto. This will help protect it from being damaged. STEP 4. Remove the cap cover with the Star Trac logo from the back cover plastics by removing the (2) screws using a #2 Phillips screwdriver. Retain the screws for later use. You will no longer need the cap cover and, if desired, you can store it away for any possible future use. STEP 5. Remove the (2) M8 buttonhead screws retaining the cross-brace using provided 5mm Hex key. Retain screws for later use. You will no longer need the cross-brace and, if desired, you can store it away for any possible future use. STEP 6. It is now time to install the Personal Viewing Screen. Remove the PVS with its mounting bracket and cables from the packaging. Also remove the (2) M8 buttonhead screws from the hardware kit in the packaging. 620-7991 Rev 002 STEP 7. Mount the PVS assembly on the mounting bracket, then thread the (4) M8 buttonhead screws through the PVS mounting bracket into the display mount. Do not tighten the screws yet. Note: (2) of the screws are in the PVS kit, (2) retained from step 5. STEP 8. Adjust the cap with the grommet into place. Using the 5mm Hex key, tighten the M8 buttonhead screws to 190 lb-in (21.5 N-m) of torque. Take the (2) Phillips head screws you removed from the original cap and snugly tighten screws down using a #2 Phillips screwdriver. Check the back side of the display to see that the cap is seated properly. If not, loosen the two Phillips Head Screws, adjust the cap and then retighten the screws. STEP 9. Using a #2 Phillips head screwdriver, remove the (4) screws that hold bottom side of the display console on. Next remove the bottom cover. Caution: When removing bottom cover, gently disconnect the CSAFE cable from the back of the display board. Retain screws for later use. 620-7991 Rev 002 STEP 10. Using a #2 Phillips head screwdriver, remove the (4) screws that hold center console to the display and remove the screw that holds in the blank cover where the new headphone jack mount will go. Next detach the center console ribbon cable then remove the center console and the blank headphone cover. Retain screws for later use. Note: You will no longer need the center console and headphone jack cover, both can be stored away for any possible future use. STEP 11. Take the new PVS center console from the kit. STEP 12. insert the new center console into the front display. Using a #2 Phillips screwdriver, screw in the (4) screws that were saved from the original center console. Tighten the screws so they are snug. 620-7991 Rev 002 STEP 13. Note: If the...

Scarica la tua

Per scaricare, digitare 2 cifre :