valutazioni - 5, GPA: 3.8
(
)
)
|
Facilità d'uso
IMPEX INC. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS PRODUCT. SAVE THESE INSTRUCTIONS. 2 3 ASSEMBLY INSTRUCTION Tools required to assembly the machine: Two Adjustable Wrenches STEP 1 (SEE Diagram 1) A.) Connect the two Rear Upright Beams (#1) by a Cross Brace (#25) in the Mid-span. Fasten them by two M10x 2 3/8” Bolts (#14), four . 7/8” Washers (#13), one Bracket (#12), and two M10 Aircraft Nuts (#15) on each side of the Cross Brace. DO NOT tighten the nuts and bolts yet. B.) Insert the Backrest Adjustment Bar (#10) through a selected hole to obtain desired incline of Backrest. C.) Insert two Bar Catches (#2) & (#6) into the selected hole on the Rear Upright Beams (#1) to obtain the desired height to hold the weight bar. DIAGRAM 1 4 STEP 2 (SEE DIAGRAM 2) A.) Connect the Front Stabilizer (#49) to the Main Seat Support (#32) and secure them with two M10 x 1” Bolts (#42), four . 7/8” Washers (#13), and two M10 Aircraft Nuts (#15). DO NOT tighten the nuts and bolts yet. B.) Connect the Main Seat Support (#32) to the Cross Brace (#25) and secure it with two M10 x 2 3/8” Bolts (#14), four . 7/8” Washers (#13), one Bracket (#12), and two M10 Aircraft Nuts (#15). C.) Connect one end of Diagonal Support (#40) to the Main Seat Support (#32). Secure it with one M8 x 2 1/8” Bolt (#38), two . .” Washers (#37) and one M8 Aircraft Nut (#36). Connect the other end to the Front Stabilizer. Secure it with one M8 x 5/8” Bolt (#27) and . .” Washer (#37). D.) Securely tighten all nuts and bolts previously installed. E.) Insert Lock Pin (#26) into the hole on the Main Seat Support (32). Only use the pin when changing the backrest board to a vertical position. DIAGRAM 2 5 STEP 3 (SEE DIAGRAM 3) A.) Attach a .7/8” Washer (#13) onto a M10 x 4 .” Bolt (#24). Insert the Bolt through the Butterfly (#22). Place a M10 Regular Nut onto the Bolt. Then insert the Bolt through the hole on the Rear Upright Beam (#1). Secure the Bolt with a Knob (#11) behind the Upright Beam. Repeat the same step to install the other Butterfly. B.) Attach the Left Butterfly Handle (#19) to the Left Butterfly (#22). Secure it with a M10 x 2 .” Bolt (#18), . 7/8” Washer (#13), and M10 Aircraft Nut (#15). Repeat the same step to install the Right Butterfly Handle (#21). C.) Attach the Leg Developer (#47) onto the bracket on the Front Stabilizer (#49). Secure it with a Hex Socket Axle (#43) and Hex Socket Screw (#46). D.) Insert two Foam Roll Tubes (#48) halfway through the holes on the Leg Developer (#47). Push four Foam Rolls (#39) onto the tubes from both sides. E.) Place a Spring Clip (#4) onto the weight holder on the Leg Developer. DIAGRAM 3 6 STEP 4 (SEE DIAGRAM 4) A.) Attach the hole-side of the Backrest Supports (#28) onto both ends of the Pivot on the Main Seat Support (#32). The other side rest against the Backrest Adjustment Bar (#10). B.) Place the Backrest Board (#33) onto the Backrest Support (#28). Fasten it with four M6 x 1 3/8” Bolts (#31) and . .” Washers (#30). C.) Place Seat Cushion (#34) onto the bracket on the Main Seat Support (#32). Align the holes and fasten the Seat with four M6 x 1 3/8” Bolts (#31) and . .” Washers (#30). D.) Insert the Arm Curl Stand (#44) into the opening on the top of the Front Stabilizer (#49). Secure it with a Knob Bolt (#41). E.) Attach the Arm Curl Pad (#35) to the Arm Curl Stand (#44). Secure it with two M8 x 5/8” Bolts (#27) and . .” Washers (#37). DIAGRAM 4 7 8 PARTS LIST KEY NO. DESCRIPTION QUANTITY Rear Upright Beam 2 Right Bar Catch 1 Curl Bar 1 Spring Clip 5 1” Round End Cap 16 Left Bar Catch 1 Bar Catch Panel 2 3/4” Flat End Cap 4 1 .” Square End Cap 12 Backrest Adjustment Bar 1 Knob 2 Bracket 3 . 7/8” Washer 20 M10 x 2 3/8” Bolt 6 M10 Aircraft Nut 10 1 1/8” Plastic Stopper 2 3/8” Bushing 10 M10 x 2 .” Carriage Bolt 2 Left Butterfly Handle 1 Grip 2 Right Butterfly Handle 1 Butterfly 2 M10 Regular Nut 2 M10 x 4 .” Bolt 2 Cross Brace 1 Lock Pin 1 M8 X 5/8” Bolt 3 Backrest Support 2 1” Flat End Cap 2 . .” Washer 8 M6 x 1 3/8” Bolt 8 Main Seat Support 1 Backrest Board 1 Seat Cushion 1 Arm Curl Pad 1 M8 Aircraft Nut 1 .3/4” Washer 5 M8 x 2 1/8” Bolt 1 Foam Roll 4 Diagonal Support 1 Knob Bolt 1 M10 X 1” Bolt 2 Hex Socket Axle 1 Arm Curl Stand 1 1 .” Square Sleeve 1 Hex Socket Screw 1 Leg Developer 1 Foam Roll Tube 2 Front Stabilizer 1 1 3/4” Square End Cap 2 Weight Plate 10# 2 Weight Plate 15# 2 Weight Plate 25# 2 Weight Bar 1 9 IMPEX INC. LIMITED WARRANTY IMPEX Inc. ("IMPEX") warrants this product to be free from defects in workmanship and material, under normal use and service conditions, for a period of two years on the Frame from the date of purchase. This warranty extends only to the original purchaser. IMPEX's obligation under this Warranty is limited to replacing or repairing, at IMPEX's option. All returns must be pre-authorized by IMPEX. Pre-authorization may be obtained by calling IMPEX Customer Service Department at 1-800-999-8899. All ...