valutazioni - 4, GPA: 4
(
)
)
|
Facilità d'uso
Door Pole, short, black, fiberglass, rubber tips 1 5010000543 5010000545 Self-Rolling Window Spring Descriptions Color Code Description Qty. Replacement Part No. Red Yellow Green Orange 5010000624 5010000626 5010000627 5010000628 CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury. Keep out of reach of children. To Set Up Tent 1. Unfold tent and spread out on a clean, level surface with the door facing the desired direction. Unzip doors. (Fig. 1)_ Pull four corners of tent taut, then secure by driving stakes through web loops at an angle for better anchoring. (Fig. 2) Assemble four, steel, shock-corded, curved Ridge Poles. Insert Ridge Poles (with red marking) into center sleeves on top of tent with the red trim (Fig. 3). Insert the remaining curved Ridge Poles into the other two sleeves on top of tent. Assemble eight, steel, shock-corded, Leg Poles. Push down on steel button on tapered end and insert into end with four holes. NOTE: Make sure steel button locks into third hole on pole as shown. (Fig.4) Insert curved end of Leg Poles (with red marking) into the ends of the Ridge Pole (with red marking). Insert curved end of remaining short Leg Poles into the ends of the remaining Ridge Poles. (Fig. 5 & 6) Curved Ridge Poles with Red Markings in center sleeves 6. Rotate all eight Leg Poles upright and insert pin on each web loop at the side locations as shown. (Fig. 7 & 7A) / 7A1 L\w r 1 Fig. 8 Locate the plastic hooks at sides and corners of tent, then snap onto Leg Poles to attach. (Fig. 8) To stretch tent to finished size: • Push in button on Leg Pole while twisting lower Leg Pole section counterclockwise (Fig.9); • Pull up on top Leg Pole section until tent is taut; • Twist the lower Leg Pole clockwise until the button locks into the center or lowest hole; • Repeat on remaining Leg Poles. Insert plastic stakes through web straps located on both sides of tent, then drive in to secure. (Fig. 10) NOTE: It may be necessary to remove metal stakes through web straps at side of tent and screen room pull tent taut, and drive in stakes to secure. Hinged, Rigid Door 1. Assemble Vertical Door Pole (shorter black pole with plastic tips); then insert through zippered vertical pole sleeve on hinged side of door. (Fig. 11) 2. Insert end of Vertical Door Pole into bottom hinge plate, apply pressure to form a slight bow, then insert other tip of pole into top hinge. Zip up vertical pole sleeve. (Fig. 12 & 13) 3. Assemble Door Pole (longer black pole with plastic cap tips); then insert into zippered pole sleeve at top of door. (Fig. 14) 4. Insert end of Door Pole into top hinge plate, apply pressure to form a bow, then insert other tip of pole into the bottom hinge. (Fig. 15) 5. Zip up pole sleeve to enclose Door Pole. (Fig. 16) (continued on other side) To Attach Rainfly 1. Drape Rainfly over tent. Make sure seams on Rainfly are facing down and centered over poles of the tent. (Fig. 17) NOTE: Hook and loop fasteners, located on seams of underside of Rainfly, should be centered over Ridge Poles. Assemble thin, black, shock-corded Awning Pole with metal tips; then insert through sleeve in Rainfly above door. Repeat the process to install the awning pole at the opposite side of the tent. (Fig. 18) Insert tapered metal tip on Awning Pole into grommet located on web strap clipped to center Leg Pole. (Fig. 19) Go to opposite center Leg Pole on other side of door and gradually apply pressure to the pole forming an arch. Insert metal tip into the grommet. Locate all hook & loop fasteners on underside of Rainfly and wrap around Leg Poles and Awning Pole locations. (Fig. 20) Insert metal hook onelastic straps on Rainfly into the hole on each Leg Pole. (Fig. 21 & 22) 7. Loop ends of guylines over stakes, stretch tight, then hammer into ground at an angle as shown. (Fig. 23 & 23A) Self-rolling Windows CAUTION: “Springs” may have sharp edges. Handle with care to avoid injury. Keep out of reach of children. NOTE: Carefully unroll metal “springs” stored in bag with stakes. The color marking on each “spring” should match the color of the fabric “flag” sewn to the window or door sleeve opening. (Fig. 24) Locate sleeve(s) in window panel, open hook & loop fastener; then insert “spring(s)” with matching color marking. (Fig.24 & 25) NOTE: When inserting into the sleeve(s), the color marking on the “spring(s)” should always face the operator. Close hook & loop fastener to secure. Before unzipping and opening the window, push in at top to engage “spring(s)” to activate the self-rolling feature. (Fig. 26) Unzip to allow the window panel to roll down automatically; zip back to close window panel. (Fig. 27 & 28) NOTE: Repeat steps above for inserting the color matching “spring(s)” into sleeve(s) for the rest of the windows. 4. Push in at top to engage “spring(s)” \ Self-rolling Windows (continued) CAUTION: All “springs” must be removed from sleeves before teari...