valutazioni - 0, GPA: 0
(
)
)
|
da questo dispositivo ha anche altre istruzioni :
Facilità d'uso
2U Rack Rail Kit for the HP
NOTE:
Rails are marked L and R with an
D3x00 Disk Enclosure
Overview
Installation guidelines
arrow indicating the direction in which the
rail should be installed.
installation instructions
This document contains instructions for installing HP rack
This installation is to be performed by qualified
rails into square or round hole racks for HP D3x00
individuals who have knowledge of the procedures,
2.
Use guide pins to align the shelf mount kit to the
devices. The rails are situated on the cabinet with
precautions, and hazards associated with equipment
RETMA column holes.
location pins and secured with spring loaded hooks that
containing hazardous electrical circuits.
The bottom of the rail must align with the bottom of
Abstract
latch onto the RETMA column. There is a shipping screw
WARNING!
These rails, when installed, form
the U.
Contains instructions for installing HP rack rails into square
in the back to secure. The front CTO screw is located
or round hole racks for HP devices.
behind a die cast latch/handle on the chassis ear.
only a shelf for the device to rest on. The device
3.
To engage the rear, push the rail toward the back
is not attached to the rail by any other means.
of the rack until the spring hook (1) snaps into
NOTE:
For more information on preparing the
Use extreme caution when pulling the device out
place.
device for installation, see the user guide that
from the rack; it can slip and fall, causing damage
ships with the device.
to the device or injury. HP is not responsible for
any damage or injury caused by the mishandling
of the device.
Kit contents
WARNING!
Ensure that the rack is level and
stable before working on the rack. Be sure the
•
Two rack shelf mount rails.
leveling jacks (feet) extend to the floor and that
•
Mounting hardware for square holes is pre-installed.
the full weight of the rack rests firmly on the floor.
WARNING!
Ensure that the rack has anti-tip
NOTE:
Hardware that is compatible for
measures in place. Such measures may include
round holes is included with the shelf kit for
floor-bolting, anti-tip feet, ballast, or a combination
the rack.
of these as specified by the rack manufacturer
•
and applicable codes.
Front and rear square hole retaining screws are
4.
To engage the front, pull the rail towards the front
provided with the kit.
WARNING!
Ensure that sufficient personnel are
of the rack to engage the spring hook with the
on hand to support the product(s) during the
RETMA column in the same manner as the rear
NOTE:
If mounting the device into threaded hole
installation process. Use of the appropriate lifting
spring hook.
or telco racks, please see www.racksolutions.com
device is recommended as an installation aid.
to purchase mounting hardware.
NOTE:
Make sure that the respective guide
WARNING!
Always load the rack from the
pins for the square or round hole rack align
bottom up. Load the heaviest items in the rack
properly into RETMA column hole spacing.
first. This makes the rack bottom-heavy and helps
Important safety information
prevent it from becoming unstable.
5.
Secure rear of rack rail to the RETMA column with
either the square- or round-hole shoulder screws,
See the Important Safety Information included in the HP
WARNING!
Do not overload the branch circuit
provided in the plastic accessory bag.
D3x00 Chassis Install Instructions with the device.
that provides power to the rack. The total rack
load should not exceed 80 percent of the branch
© Copyright 2014 Hewlett-Packard Development Company, L.P.
Printed in the US
CAUTION:
Electrostatic discharge (ESD) can
circuit rating.
damage electronic components. Be sure you are
nl
nl
properly grounded (earthed) before beginning
nl
nl
nl
any installation procedure.
nl
nl
nl
nl
nl
nl
nl
nl
nl
nl
nl
nl
HP Part Number: 734750-001
nl
Installation procedures
nl
Published: March 2014
nl
nl
Edition: First
*734750-001*
nl
1.
Position left and right rack rails at the desired 'U'
nl
nl
position in the rack, adjusting the rails to fit the rack,
nl
nl
nl
as needed.
nl
nl
6.
Secure front of rail to the front RETMA column using
nl
Front and Rear bottom edge of the rails must align
nl
the provided flat securing screw/guide pin in the
nl
nl
with the bottom of EIA boundary in the lowermost
nl
bottom screw position of the rail.
nl
'U'
nl
nl
Page 1
... Questo manuale è adatto anche per i modelli :
dati dispositivi di elaborazione - HP D3600 w/12 2TB 6G SAS 7.2K LFF(3.5in) Midline Smart Carrier HDD 24TB Bundle (434.87 kb)
dati dispositivi di elaborazione - HP D3600 w/12 3TB 6G SAS 7.2K LFF(3.5in) Midline Smart Carrier HDD 36TB Bundle (434.87 kb)
dati dispositivi di elaborazione - HP D3600 w/12 4TB 6G SAS 7.2K LFF(3.5in) Midline Smart Carrier HDD 48TB Bundle (434.87 kb)
dati dispositivi di elaborazione - HP D3700 Enclosure (434.87 kb)